Really coming along! Looking good man!!
You have a nice set up going man. I might have missed it but do you have any kind of air filter down there for fine dust? I have my shop set up in my basement too and its such a pain doing anything just because I end up with a fine layer of sawdust throughout the entire basement.
Thank you sir and NO! Unfortunately yesterday was a wake up call for me. Now I do run two Festool Midis which are perfect for DC and filtration but that cut I made last night was with my Dewalt 20v (which did AWESOME!) and the dust was unbelievable. Stupid stupid stupid rookie mistake. Now I am thinking about doing just that and getting a filter for the whole basement. Have you had any luck with finding any that peak your interest?
it made a big difference for me once I ported the exhaust from my shop vac directly outside…….
Yeah I’m thinking about a whole filtration unit though. I’m looking into a non staticky dust deputy for my midi to conserve bags but for the tools that’d aren’t as efficient in DC wouldn’t the whole room one help out?
This guy built a dust filter for his shop.
The commercial built units are 300 to 400 dollars.A good Hepa or close to Hepa vacuum should exhaust next to dust free air.
Thanks Jason! That’s awesome!!
I have a crude one where I just attached a furnace filter to the back of a box fan and that helped a little bit but it has to be very close to whatever tool I’m using. It works okay with my miter saw but anything that I’m cutting with a circular saw just covers the entire basement. I started looking into one from Shop Fox, model W1830, and one from Jet, model 708620B. I’ll probably end up going with the Shop fox one just because its cheaper and the Jet seems to be overkill for my small area that I work in.
I’d also like to get a dust deputy soon, it seems like that would definitely save some headaches with having to constantly blow out my shop vac filter.
that guy doesn’t mess around with glue and clamps lol
Got him Madman, thanks!
The only thing I would do different is have it set up to use the 4″ furnace filters. The little one inch is kinda lame plus they will get clogged up quick. It’s an easy fix you just need to make it a little bit bigger to accommodate the deeper filter.
Grizzly has some air/dust filters as well. They go down to one micron. They are either hanging or benchtop and the smaller one run less than $200.
Thanks for that Nicholas, I will check out the site right now. Really dumb thing to last night.
Well all makes those mistakes, the best thing u can do is have a camera running. So we can all have a good laugh.
did anyone watched part2 of the air filter video? his bit extension is funny 😀
madman_us wrote:
did anyone watched part2 of the air filter video? his bit extension is funny 😀
Yeah that was pretty funny. I still can’t get over how much glue the guy used to put that thing together, he must go through about a gallon a project.
Glue? A gallon? That’s cause he’s sniffing it between puffs!
ChrisK1970 wrote:
Thanks for that Nicholas, I will check out the site right now. Really dumb thing to last night.
Maybe dumb thing to do but we live and learn. You should never cut fiber cement board in side and always wear a mask. Silica dust is as bad or worse than asbestos it can harden in your lungs. Google Crystalline silica one time.
Silicosis isn’t joke. I think that’s why we are seeing all of the dust collection on sds tools.Well it also helps for any sort of anchor preparation, and keeps a cleaner jobsite but that’s one of the reasons.
When I first went to work for the Utility we would use a rock wheel to do road cuts Dust and everything would fly when I left 35 years later you had to wear a supplied air mask when operating and a full face mask when working around it. Here is what a rock wheel is and this is low dust there where times you could not see you hand held in front of your face.
no shit, my first job was in a chrome shop…..we wore rubber gloves around the tanks that is about it…..chromium trioxide, costic soda ect ect now they have to wear hazmat suits…..
NicholasShetley wrote:
Grizzly has some air/dust filters as well. They go down to one micron. They are either hanging or benchtop and the smaller one run less than $200.
General International makes 2 nice hanging air filters I will be getting one as soon as i start my shop.
Wow that cement cutter is freaking crazy!! I never seen anything like that used around here. I just see the usual cement saw and that’s it.
that’s a huge blade on that machine.
back towards that glue video – I think that guy sniffs other stuff instead of glue .P
Well that may be but he is funny!’it’s like that episode of Friends when Monica (?) rides that really funny guy who drinks too much until he stops then he becomes a whiney bore! If it works…….;)
i would tend to go for a specific built unit, they must be more efficient but not sure… gotta weigh out time vs cost savings and figure out what works better for you.
woodcraft always seems to have a sale on the smaller Jet ceiling mount filters
grizzly seems to be a good source too.
http://www.grizzly.com/search/?s=category%3aDust+Collectors&rankBy=price%3aascending
only $160 http://www.grizzly.com/products/Hanging-Air-Filter-3-Speed/G0738
Thanks John!
So I went to Woodcraft in Newington NH today to look at…..yes you guessed it….some Festool stuff. While talking to the store manager Mark I was explaining that I needed to go to HD this weekend and get another shop light. Anyways he says “you want to buy some really nice Freud Marketing lights” I said I’d look. I walked out with three brand new Freud wrapped fluorescent lamps. T8 single 48″ lights in a under cabinet box with huge Freud name plates on the front. $50! I’ll post a picture as soon as I airdrop them to my iPad!
nice chris – that’s a good deal
Thanks Madman. These are really special, I really lucked out with that and three! I might try to sell one on CL and that’ll pay for the lights but I am not so sure. Nice thing is they came designed to fit under the woodcraft upper shelves so they are equipped with grounded plugs. I might cut them and direct wire them with chain pulls though.
That’s a sweet deal u scored. Sometimes right time, right place.
how much you want for one? if you gonna sell it
some guys have all the luck!……nice find/score……
Nice score there bro those look cool!!
That will be a pretty sweet detail in the shop!! Nice
Yeah they’re going to look great when I get them in. I didn’t get to work on the shop at all today. Preparation for the storm Monday they are forecasting 1′-2′ of super heavy cement snow. Plus my wife and I were upstairs working on our future suite remodel. Samantha abused the heck out of some wall studs with my Milwaukee M12 Fuel hackzall. She (and it) did awesome!
Know Chris that would have been a awesome pic. Your wife with the Milwaukee. You must really love her to let her play your tools.
would he do the same if it would be festool ? 😛
Probably not.
Well guys actually I am running ONE midi downstairs in my shop because Samantha has the other one and my RO90 and ES125 sanders upstairs in the bedroom! I’m very nice to her. Everyone else can kiss my lily white New England A$s!!!!!
Hey Chris I joke about my wife playing with my tool. However in the end, she play with whatever she wants. It’s great when u can both handle the power tools, it makes those honey do list seem a lot smaller.
Geez… I have to beg my wife to play with my tool……. ??? Wait, are we talking about the same tool ???:)
Wait a second….now I’m confused….which tool???????
Same here?
lets stop talking about “tools” for a second and lets go back to the main post 😛
It’s funny how leaving the s off can change the whole meaning.
lets see how much time it takes to get off track again…..
are your lamps mounted yet chris? 😛
Nah not yet Madman. Truthfully I just got them downstairs and was trying to figure out where to put the first one. They are pretty heavy and I’ll have to enlist my Wife to help me out!
as soon as they are up – give us a picture 😛
