NicholasShetley wrote:
I wouldn’t get your hopes up on the end of January thing because it takes a good while to do all of it. If it is a rust free truck it could be done but I would say by the end of February since it is just you and since you have school and such. The paint brand I would go with would be DuPont. Yes it is expensive but it will be worth it in the end. It will last 20+ years if you take care of it. I would definitely price the paint before you get started. I’m not trying to talk you out of it, I’m just saying it is more time consuming than most people think.
The local shop who does great work quoted me at 850 and thats for everything from prep to primer to paint. I am going to do all the wet sanding, and all trim removal, and send it to them for paint. as for the truck it is rust free, a few dents i have to pull and bondo but no big deal.
Is that just labor? That is way too cheap.
It was 1800 for just the paint for my grandpas corvette back in 2000
NicholasShetley wrote:
It was 1800 for just the paint for my grandpas corvette back in 2000
1800!!! No in central florida here that is the most expensive place, they have some nice cars roll out of there, and that was an over the phone quote but some where below a 1000.
He got the absolute best of the best paint DuPont had. The dents aren’t too bad to deal with, just hammer it somewhat smooth and put bondo on it then sand it smooth. I have always sanded in an x pattern, it keeps the surface from getting wavy.
NicholasShetley wrote:
He got the absolute best of the best paint DuPont had. The dents aren’t too bad to deal with, just hammer it somewhat smooth and put bondo on it then sand it smooth. I have always sanded in an x pattern, it keeps the surface from getting wavy.
ok, they arnt to bad one small one on the front fender and on the back right is not to bad, looks like someone sideswiped a pole.
That isn’t bad at all.
Nicholas there are a lot of things that go into a paint job when you do a high range car like a Vette. When you paint a high end car you do extras like removing moulding and lights, more expensive paint, more coats of primer and clear. A basic paint job you just tape off everything. Plus like my autobody teacher taught us if you own a high end car you are likely to pay a premium rate because there are higher expectations, even if everything is equal.
He did everything himself though. He was a body man out of high school for a while. He put about 10 coats of clear on it.
There you go. Average is 2-4. He probably used a coat of self etching sealer or zinc chromate as a base, then a color matching primer too, right?
He used the etching primer, then the color matching primer, and paint, ect.
NicholasShetley wrote:
He used the etching primer, then the color matching primer, and paint, ect.
It’s amazing what a difference proper primer application makes on a project.
Looking good man!
Yes it does. We were surprised how forgiving the flat black was as well, it didn’t show a single sanding mark.
NicholasShetley wrote:
Yes it does. We were surprised how forgiving the flat black was as well, it didn’t show a single sanding mark.
I’ve always had good luck with flat personally.
He had heard that it was but we weren’t sure.
Today we cut the aluminum insulation stuff to fit in the cab. It fit excellently in all of the cab. I didn’t take any pictures today or I would post them.
Today we painted the firewall. I will try to have pictures up later.
All that sounds like fun, well just the aluminum cutting part. I hate painting although I’m sure painting walls is a lot different than painting metal work.
Here is what the cab looks like with the insulation installed. We didn’t have it glued in at this point. I didn’t take any pictures of the firewall today because it was still taped up and the cab was covered up. I’m sure that painting cars is way different than bricks.
Javier wrote:
All that sounds like fun, well just the aluminum cutting part. I hate painting although I’m sure painting walls is a lot different than painting metal work.
A spray gun is 10X’s more fun than a brush. No doubt about it.
Here is what the cab looks like now. I painted the firewall. Today we test fit the doors and glued the insulation in. Next is to do some work to the front and rear end.
Looking good buddy! The car is awesome, but the memories will be priceless.
Thanks conductor! I bet the memories will.
That vehicle keeps looking better and better.
@ conductor, I hear you, painting walls with a brush would take ages
Are you sure you are going to want to drive it? It’s looking show quality.
We don’t build trailer queens here Harold. Every one around here drives their cars all of the time. The only question is will it handle as good as it will look.
You throwing a big block chevy in there? That thing will get up and go!
No just a small block. A small block will be more than enough though. He had a model a roadster that had a small block in it and he said it would light up the tires when ever he wanted to. This one shouldn’t be any different.
Never heard of Trailer Queens. Funny. Have you ever heard of Lot Lizard? 🙂
Yes but thankfully I have never seen one. So that is why semi trucks have sleeper cabs lol.
We have trailer lizards here. Kinda like Lot lizards only they work out of mobile homes
We get way off subject here don’t we.
Sorry. My bad.
We made zero progress today. We had to change the transfer case and change the transmission fluid and put rear brakes on his truck today. He should be set for a good while now.
We finally put the doors on and the latches, handles, and trim. The passenger door fit perfect but the driver side door was all out of whack. My grandpa said that it had fell onto one of the corners so that is what caused it. The latch was too big as well so we had to grind it down (could have used the AC Delco grinder there, thanks again guys). Then where it latches was too low so we had to make a spacer for it. After that it finally fit. I will take pictures Monday because with a minimum of 8 inches of snow school will most likely be cancelled.
I hate doors and hoods, they are the biggest pain to try and get to set right.
It took us two days. For it being 85 or so years old it wasn’t too bad.
Here is what it looks like with the doors on. We also did some work to the front end and test fit everything. It all looks like it will work out good. That is dust on the door if anyone was wondering. If you look in the second picture you can see where we had to grind the latch down so it would engage. In the third picture we had to make a spacer so the latch would fully engage. You can adjust that piece so the door can fit tight.
Looks it’s coming along nicely. Looks great. When you plan on having it done?
We would like it done in time for senior prom in late April. The interior is almost ready to go to the upholstery guy. The front end is almost done except for paint. The engine and transmission won’t take more than two weeks. I think we should get it done in time. If we don’t I will take his corvette like I did last year.
Looking good. Nice pictures keep them coming
Looks great, good job. What type of material are the seats going to be? Fabric or leather?
I’m not sure yet but the guy is supposed to be out to see about the interior later today. He already had them upholstered but he needs them redone to match the paint scheme.
Well I might have to put that project on hold since dads truck blew the motor yesterday.
NicholasShetley wrote:
Well I might have to put that project on hold since dads truck blew the motor yesterday.
That sucks for your dad and you.
His poor truck has over 500,000 miles on it (not on the engine). We have another 454 to put in it that is in better shape. It was starting to burn oil and wasn’t running near as strong. It won’t be too big of a project, couple days at the most.
Atleast you guys know how to fix it
And have a warm space to work on it in. The entire driver side of the engine bay is soaked in oil. We think a valve fell to cause it.
Good thing you guys are working on it. I remember my first car had an oil leak and went to the mechanics to get it fixed. They fixed it but the jerks didn’t have the decency of wiping the leaked oil sitting at the bottom of the engine. I don’t know if its laziness or negligence or even a money thing as I would have gladdly paid them for the price of their shop towels if they got ruined.
To cut to the end of the story, every other time I got my car serviced, they kept telling me it was leaking although the leak was fixed. They were simply looking at oil from the leak before it got fixed.
Most people would scrap it if it was theirs. It is worth less than 1500 but the thing is in perfect mechanical shape. The story you listed above is why we do our own work because unless you know the people doing the work I wouldn’t trust them.
