Ryobi battery riding lawn mower

Roger D.Member since Jun 2022

jamis wrote:

On 6/28/2021 at 3:36 PM, jamis said:

AFAIK, the AUX position of the key switch has never worked on these mowers. According to the troubleshooting manual and my mower, there is nothing connected to the AUX lug on the bottom of the switch.  Run time is  going to be affected by the ability of all of the batteries to hold a charge under load.  It only takes one of the four batteries to bring the system down.  Since the system shuts down when the pack voltage drops to 36 volts, if one battery fails to hold a charge under load, you can see reduced run times.  Therefore, measuring the voltage at the beginning and the end of any usage will help you understand what’s going on.  My 34 month old batteries can sit for a week or more without needing a maintenance charge this summer, but they will still mow for over an hour and a half before getting into the red zone.  My batteries have 195 charge cycles on them also.  It’s really too bad Ryobi decided not to utilize the voltage and percentage functions of the BLM.  The information would be most useful for owners.

I bought my RM480e @ HD back in Sept 2018 as a refurb. Between this forum and YouTube I learned how to do al lot to this mower (new batteries, new transaxle fluid, align and lube the steering, and the meter mod). But thru all this I found a quirk in the key switch on my mower (and curious if all RM480’s are like this). Seems I didn’t need the key to turn the unit to the “on” position- anything that would grab the keyhole (such as a slotted screwdriver) could turn the switch. The key was only needed to turn the switch to the “AUX” position (which has nothing connected to it). I got a new switch from Ryobi and it did the same thing. My fix was to move the two wires from one side of the switch (the white “ON” position) to the other side (the grey “AUX” side). Then I re-labeled “ON” to “AUX” and “AUX” to “ON”. I alerted Ryobi on this quirk but have yet to hear anything back from them. Just curious if there are any more 480e’s like this.

jamisMember since Apr 2010

Yes, Mine purchased in Aug 2018 is the same. The other four Ryobis on my street are also like that, and one is new this year.  it’s likely a design flaw with the Homelight made switch. Never understood why the AUX position even existed since there has never been any accessory PTO function or wiring on the mowers.

Roger D.Member since Jun 2022

jamis wrote:

19 hours ago, jamis said:

Yes, Mine purchased in Aug 2018 is the same. The other four Ryobis on my street are also like that, and one is new this year.  it’s likely a design flaw with the Homelight made switch. Never understood why the AUX position even existed since there has never been any accessory PTO function or wiring on the mowers.

Thanks for the info Jim. You confirmed my hunch that mine wasn’t unique and I just put the info out there for those individuals who are paranoid, like myself, about getting their mowers stolen.

jamisMember since Apr 2010

Roger D. wrote:

7 hours ago, Roger D. said:

Thanks for the info Jim. You confirmed my hunch that mine wasn’t unique and I just put the info out there for those individuals who are paranoid, like myself, about getting their mowers stolen.

I guess I never thought someone would try to steal a 600-700 pound mower. I always take the key out of the switch when I not on it, mostly so kids won’t try to play with it. There is one neighbor boy who hasn’t learned to respect other people’s property.  I also don’t leave it out when I’m not using it. Mine is stored at the back of the garage with a car parked in front of it. I have to pull the car out of the garage to use the mower, a situation quite a few of my neighbors also have with their riding mowers.

jamisMember since Apr 2010

Just got my electric bill for June. Surprise! The rate dropped from $0.13/KWH to $0.06/KWH. 87E10 here is varying between $4.79 and $5.10 a gallon. The drop in the electric rate makes my mower even less expensive to operate than an ICE mower.  The big reason for the drop in rate is due to my electric generation is 100% green (solar & wind) and the non-green generation here is nuclear & natural gas powered with some coal.  Our county has an agreement with the electric utility to allow the customers to choose who generates the electricity and one of the suppliers has the 100% green option. Last month’s green generation cost was $0.02/KWH. The rest was transmission charges by the utility. I know folks in other parts of the country have higher rates, so I’m not bragging,

but I wonder how many have choices in how their juice is done?

fyrfytr998Member since Mar 2022

The front of my house may look weirder now, but gong solar was one of the best decisions I ever made. Even paying the lease option, my electric bill is smaller than pre solar bills.  $600/700 dollar bills are now down to $200/300ish including the lease payment of $150. 

jamisMember since Apr 2010

I confess that after four years of use, I really don’t understand how these batteries really work. 130 hours of use and 350 charge cycles with each charge recorded have left me unsure how these things behave. Last week, I mowed for 38 minutes, used 1.3 volts and it took 1,650 watts to recharge the battery pack to solid green. Today, I mowed for 33 minutes, used 1.3 volts and it took 790 watts to recharge the batteries to solid green (probably the lowest ever recharge).  Both mows were 1/4″ dry cuts and the temperature was 86 & 83 degrees. If you look at all of the 1.3 volt uses, the recharge watts are anything from 790 watts to 1,970 watts and run times ranged from 32 to 46 minutes with no correlation between run times and recharge watts. Confused as usual.

RegRMember since Jul 2022

Aright: I read through this whole thread to ensure no one else had asked about this problem. When starting my 480e freshly charged in the shed, something inside the mower is clicking frantically and the volt display goes haywire. What’s weirder is, the voltage doesn’t update. Eventually, by some miracle, it does eventually start correctly, the voltage display updates correctly, and then it’s ready to roll. From there I have no power issue compared to when I got the mower the previous year so it’s not a battery problem I believe. Seems like whatever controller box under the dashboard panel is the problem because it sounds like the frantic clicking is coming from it? 

jamisMember since Apr 2010

RegR: A couple of questions and comments to assist with your question. First, have you modified the Battery Level Meter (BLM) to show volts, percentage, and hours? At key on, the BLM will show a series of numbers ending with the hours run. Ryobi has stated the other numbers shown are meaningless for the user. The “48” shown is NOT the pack voltage. The actual pack voltage immediately after the charge cycle completes will be well north of 50 volts, usually 51 to as much as 57 or more. Actually, the charger will accept a pack voltage up to 67.2 volts. The batteries will slowly self-discharge just sitting and that’s the reason for having the mower plugged into the charge when not in use. The charger logic will initiate a charge cycle when the pack voltage falls below about 50 volts. Secondly, there is a master control relay that engages when the key is switched on. The relay is located on the right side of the mower down next to the battery tray along with the deck motor controllers behind the right side cover.  There is no relay under the console panel. The relay circuit checks that the seat switch is engaged (operator is seated), the charger is not plugged into the charging port, and there is sufficient charge in the pack to operate the mower. I haven’t checked, but it also may check to see if the blade PTO switch is not engaged. Third, my first guess is the seat safety switch. There are five of these mowers on my street and a couple of them (mine included) have had the seat safety switch work loose from its mount and cause some operational issues. Pushing the switch back into the seat mount until it clicks into place has corrected the problem.

RegRMember since Jul 2022

jamis wrote:

On 7/17/2022 at 12:04 PM, jamis said:

RegR: A couple of questions and comments to assist with your question. First, have you modified the Battery Level Meter (BLM) to show volts, percentage, and hours? At key on, the BLM will show a series of numbers ending with the hours run. Ryobi has stated the other numbers shown are meaningless for the user. The “48” shown is NOT the pack voltage. The actual pack voltage immediately after the charge cycle completes will be well north of 50 volts, usually 51 to as much as 57 or more. Actually, the charger will accept a pack voltage up to 67.2 volts. The batteries will slowly self-discharge just sitting and that’s the reason for having the mower plugged into the charge when not in use. The charger logic will initiate a charge cycle when the pack voltage falls below about 50 volts. Secondly, there is a master control relay that engages when the key is switched on. The relay is located on the right side of the mower down next to the battery tray along with the deck motor controllers behind the right side cover.  There is no relay under the console panel. The relay circuit checks that the seat switch is engaged (operator is seated), the charger is not plugged into the charging port, and there is sufficient charge in the pack to operate the mower. I haven’t checked, but it also may check to see if the blade PTO switch is not engaged. Third, my first guess is the seat safety switch. There are five of these mowers on my street and a couple of them (mine included) have had the seat safety switch work loose from its mount and cause some operational issues. Pushing the switch back into the seat mount until it clicks into place has corrected the problem.

Checked all connections and found nothing lose. Finally took the time to get into the mower and found the relay. After disconnecting it and taking it inside, I could see that the seal had failed and some dust/grass had entered it and was leaving charing on the plates connections. Took some time but was finally able to locate a place to order a new one. Will update if the new part works!

jamisMember since Apr 2010

RegR wrote:

3 hours ago, RegR said:

Checked all connections and found nothing lose. Finally took the time to get into the mower and found the relay. After disconnecting it and taking it inside, I could see that the seal had failed and some dust/grass had entered it and was leaving charing on the plates connections. Took some time but was finally able to locate a place to order a new one. Will update if the new part works!

I’m not surprised things were dirty under the covers. When I pulled the battery tray for a failing battery after 11 months, I found all sorts of detris inside all over everything. I now remove the battery panel on top of the mower after each mow and use my leaf blower to blow out under the covers as well as the mowing deck. 190 mph air does a pretty good job without having to remove the covers.  

jamisMember since Apr 2010

I recently received an answer to some questions about the SC-48 charger supplied with these mowers from Delta Q, the maker. They supply chargers to the golf cart market and to some high end cart makers. The one question that was answered was concerning “sulfation” of the SLA/AGM batteries. The answer was that the SC-48 charger used with the Ryobi 48 volt mowers performs a desulfation procedure during the finishing phase of a charge cycle. So every time the charger does any sort of charge cycle, it is reducing the chances of the batteries forming sulfates on the internal grids. This helps extend the lifespan of the batteries along with the 30% DOD limit the Ryobi system imposes.

 

 

 

 

Eric SMember since Sep 2021

Been awhile since posting.  Swapped out original batteries for four new Mighty Max 100ah one’s back in early May.  
 

Extremely dry conditions in Wisconsin this year as I’ve only mowed 4 or 5 times since early May up until yesterday.  

 

Mower has been plugged in entire time when not in use.  3/4 acre is mowed each time.  Battery indicator drops from 100% to 90 % when done.
 

Cost was $756 and change for the new batteries at Home Depot.  I ordered online and I picked up in store.   

jamisMember since Apr 2010

Thanks for the update. If I have to replace my batteries I will also go with the MM units. BTW, you can also order them directly from MM and they will ship to your address. 

JeremyAMember since Jul 2021

Eric,

 

How many seasons and hours did you get out of your batteries before replacement?

 

Thanks!

jamisMember since Apr 2010

Eric stated in an earlier post he got four seasons out of his original set of batteries and he also stated he is using a Power Pulse de-sulfator add on. FWIW, my batteries are in their fifth mowing season (49 mos. total ownership) and run pretty much like new. The mower has 208 mows for 140 hours of use with a total of 369 charge cycles including four winters of  four month winter storage periods. I pay $0.13/KWH for electricity and the mower has consumed $39.34 of electricity over the 49 months. That aggregates to $0.82/month or $0.24/hr of run time cost. After deducting the cost of electricity, the mower has saved $485.09 in 87E10 cost. It is currently 14 times less expensive to run than a comparable ICE mower. One more year of mowing should have saved enough to buy a full set of replacement batteries.

 

BTW, I wrote to Delta Q, the maker of the charger used in these mowers and they stated the charger does a de-sulfation cycle during the finish phase of the charging cycle. Leoch states in their documentation that these batteries should do 1,500-1,700 charge cycles based on the way the system manages the DOD. Damage from vibration can still shorten the lifespan of these batteries.

 

Interestingly, Ryobi has stated that their new 80 volt lithium battery packs are good for 1,000 charge cycles and will cost $1,300 each according to the parts ordering web pages. I can replace all of the SLA/AGM batteries in my RM480e for $640 for Mighty Max batteries or $860 for Leoch batteries. 

 

 

Eric SMember since Sep 2021

Yep, 4 seasons but the last season, last year was a real struggle to get anything more than 20-30 minutes cutting time and that was from a fully charged overnight session, at least 10 hours of constant charging.  My backyard is relatively flat but my front yard does have a septic mound and road ditch so I really noticed the battery meter dropping fast when cutting up front.  I’m going to try something different this fall for the first time and pull all four batteries and bring them inside to a heated space, hook them up in parallel on a battery maintainer and let them sit like that over the winter months.  It gets brutal cold up here in Western Wisconsin, sometimes -20 and -30 for days on end.  I called Mighty Max before I ordered them and actually spoke to a technician who said it would be better if they were in a warmer environment and hooked up to a battery maintainer in parallel.  I bought a 4 amp Harbor Freight model that the tech said would be fine to use.  Basically set it up and check on it occasionally.  Buying 4 new batteries is spendy.  Trade off’s I guess.

jamisMember since Apr 2010

My neighbor just bought four 100 ahr. Mighty Max batteries for his four year old RM480ex from HD.  He has been having run time issues and mows four lawns between 10,000 and 16,000 sq.ft each, plus he plows snow in the winter for most of the 16 homes on it, and tows lawn implements, so he uses it year ’round. He has way over 300 hours of use on the mower, with close to 700 charge cycles and has frequently run the charge down to the red zone.  He has probably saved enough in gas to pay for the new batteries.  My four year old RM480e with 142 hours of run time is still able to run for two hours of mowing, but my average run time after 49 months is under 41 minutes and uses about 10% of the available charge on average.

jamisMember since Apr 2010

BTW, I have read of at least one user in Canada who uses a large battery blanket on top of his battery box to keep things above freezing during winter storage.

JeremyAMember since Jul 2021

Have any of you ever considered removing the motor covers from the motors on the mower deck? I  feel like they

seem more likely to accumulate grass and hold it next to the motors than keep it away – especially if you blow it off after each use. I remove them to clean them off, but I am considering just taking them off completely.

jamisMember since Apr 2010

I blow my mower off after every use and use the turbo mode (195 mph). I also pull the battery cover under the seat and blow everything out under the covers. That area accumulates a lot of detris during normal use. When I pull the deck this fall to clean it for winter storage, I’ll post what the motors look like then.

jamisMember since Apr 2010

My neighbor received his four new Mighty Max 100 ahr. batteries from HD last Thursday and proceeded to charge them one at a time with his 12 volt automotive charger. They were all at about 12.5-12.8 volts as received. All went well until one started “hissing” during the charging cycle. It went on to fully charge, but the sound worried him. A call to MM told him to immediately return the hissing battery and not to use it. He’s now waiting for a replacement to be delivered maybe tomorrow. The noise was internal and the battery case is not leaking or cracked anywhere. 

jamisMember since Apr 2010

The neighbor got the defective battery replaced and his mower runs like it day one four years ago. The Mighty Max batteries appear to be fine.

jamisMember since Apr 2010

Does anyone know how to reset the hour meter in the BLM? I have 145 hours on my mower and the meter no longer shows tenths of an hour and I mow less than an hour each time. I use my cell phone for time monitoring, but I’d like to see the time on the meter. The hour meter reset itself to zero once at around 36 hours and my neighbor’s has reset itself twice. 

jamisMember since Apr 2010

The neighbor that replaced the original Leoch LPC12-100 batteries with the Mighty Max 100 ahr. equivalents discovered the battery cases are slightly smaller than the Leoch 100 ahr. cases. He had to make up wood spacers to get the clamps to hold them tight. Also, the rope handles interfere with the hold down clamp frame and plastic covers. The new batteries power the mower great though. Just something to be aware of if you go with the MM option.

JoeFMember since Oct 2022

jamis wrote:

On 10/5/2022 at 10:26 AM, jamis said:

The neighbor that replaced the original Leoch LPC12-100 batteries with the Mighty Max 100 ahr. equivalents discovered the battery cases are slightly smaller than the Leoch 100 ahr. cases. He had to make up wood spacers to get the clamps to hold them tight. Also, the rope handles interfere with the hold down clamp frame and plastic covers. The new batteries power the mower great though. Just something to be aware of if you go with the MM option.


I just replaced my (75Ah) batteries with the Mighty Max 100Ah batteries a few weeks ago (mower had about 95 hours on it and the useable capacity was no longer sufficient). For me, I had to adjust the bolts on either end of the tray, practically all of the way out, to get the new batteries to fit. There may be a small amount of additional gapping between the batteries, longways, but it wasn’t enough to make me have great concern.

I also left the rope handles on and was able to maneuver them over the battery covers and towards the outside edges of the frame that rests on top of the battery pack.

The most drastic change I made was to trim the vertical lip off of one edge of the battery covers, as they would otherwise overhang on one side of the batteries, and be sitting up on top of the other side.

Side note: The meter showed about a 50% charge level from being stuck at what it had showed before it was last charged (as they sometimes do). When I tried plugging in the charger, disconnecting it, and turning the key back on, as I’ve had to do several times in the past, it wouldn’t reset to 100%. I went ahead and replaced the batteries, fully topped them off individually, before reconnecting them in series, and then the first use or two of the mower on the new batteries resulted in zero movement on the battery meter (stayed at 50%, even after charging). It wasn’t until I used it longer and brought the meter down further that it finally reset after a charging cycle.

[External image (i.postimg.cc), not copied]

[External image (i.postimg.cc), not copied]

[External image (i.postimg.cc), not copied]

Eric SMember since Sep 2021

I did end up removing all four Mighty Max 100ah batteries near the end of October and put them in my basement.  Instead of hooking up in parallel like I originally thought I would I instead bought four individual 4ah Viking charger/maintainers from Harbor Freight ($30 each).  Each battery has its own charger/maintainer.  Each battery took between 10-12 hours to come up to full charge.  Once they reached full charge the maintainer portion took over.  Each battery stays at 13.6 to 13.7 charge.  I check them every couple days and everything seems good.  I’m hoping by moving them inside where the temperature stays at 68-70 consistently the batteries life will be prolonged.  
 

I saw a video on YouTube from a guy in Canada that is now using individual 10ah NOCO chargers/maintainers instead of the charger that came with our mower.  Might be something to consider this spring when I put the batteries back in the mower.  I figure I can use the same individual Viking units I already have.  

jamisMember since Apr 2010

My mower is in its fifth winter storage and has 145 hours of use with a total of 447 charges including winter storage. As the batteries have aged, they self discharge faster than when they were new. This winter, they are doing an average of 97 watts per day to maintain the packs in charges of 10-20 watts per charge. The batteries have always used more and more charges each winter storage as they have aged. This is the reason Ryobi states to always have the mower on the charger when not in use. If the pack voltage falls below 36 volts, the charger logic will not charge the pack. When spring comes and regular mowing resumes, the batteries have always resumed their ability to hold a charge for a week or more. By then, they are being subjected to the routine DOD and behave like they originally did.

EricLMember since Apr 2022

jamis wrote:

On 1/25/2023 at 11:25 AM, jamis said:

My mower is in its fifth winter storage and has 145 hours of use with a total of 447 charges including winter storage. As the batteries have aged, they self discharge faster than when they were new. This winter, they are doing an average of 97 watts per day to maintain the packs in charges of 10-20 watts per charge. The batteries have always used more and more charges each winter storage as they have aged. This is the reason Ryobi states to always have the mower on the charger when not in use. If the pack voltage falls below 36 volts, the charger logic will not charge the pack. When spring comes and regular mowing resumes, the batteries have always resumed their ability to hold a charge for a week or more. By then, they are being subjected to the routine DOD and behave like they originally did.

I moved my early-spring, 2021 48v ZT540e to the garage this winter, wanting it to be a bit more insulated than the wood shed used previously.  I have also taken to quickly unplugging the charger then plugging it back in to initiate the topping off during the offseason, and every time it has indeed recharged upon replug.  Just now I wheeled it out and engaged the blades to mulch up some leaves, and it pretty quickly went from 100% down to 95 and then 90%, with a temp of 60° here in nrn MD.  The pack read 50.6v on the meter while blades were running at 90%, and jumped up to 51.7 when I turned the blades off.  I am hoping this work extends the battery viability… but I know it’s early and the verdict is still out.  This will hopefully be season 3 w the original batteries, but I am wary.

jamisMember since Apr 2010

Ryobi has announced two new 80 volt riders. A 42″ & 46″ cut with 10 ga. fabricated decks. The look like front engine ICE mowers with the three battery packs in where the engine would be. $4,999 & $5,499.  My 54 month old RM480e is about to pass  1,700 charge cycles on the original batteries. 

GartenmeisterMember since May 2022

Is it current consensus that the Mighty Max ML100-12 is the best value in replacement battery?  $179.99 at HD, $1 more at Lowes but Lowes’ card gives a discount.  Thinking of ordering 4 as my mower runs for about 5 minutes cleaning up leaves.

JoeFMember since Oct 2022

Gartenmeister wrote:

On 3/22/2023 at 1:22 PM, Gartenmeister said:

Is it current consensus that the Mighty Max ML100-12 is the best value in replacement battery?  $179.99 at HD, $1 more at Lowes but Lowes’ card gives a discount.  Thinking of ordering 4 as my mower runs for about 5 minutes cleaning up leaves.


It was when I bought mine 6 months ago.

I got mine from Zoro.com because I was also able to apply a discount code and get an extra $103.80 knocked off the total cost.

TotalRexMember since May 2022

Last year I bought 4 new batteries.   I made sure to charge them and kept my mower in in the garage on the charger during the winter.

Now the gauge only goes to about 1/4th charged and when the mower lasted only a few minutes before it stopped mowing.

 

I have to believe the batteries are OK.  Could this be the charger, or gauge or something else?  Any ideas?

Eric SMember since Sep 2021

Still have all 4 Mighty Max 100ah batteries on individual 4ah Viking charger / maintainers.  No need to hook back up to the mower anytime soon since we just got another 10” snow this past Saturday.  Batteries have maintained 13.6 or 13.7 volts since last October when I took them out of the mower and brought them inside the house for the winter.

GartenmeisterMember since May 2022

Well, now my mower won’t drive.  Blades and lights work for whatever that’s worth.

 

It makes ONE beep when I close the control levers and it won’t move, forward or reverse.  The diagnostic code chart in the service manual says one beep has to do with “angle sensors” but there is no reference to angle sensors anywhere else in the document.

 

Any  ideas?

JeremyAMember since Jul 2021

Posting this just for others information…

 

My mower was new in June of 2021 – has 60 hours on it and I mow 1.25 acres (90ish minutes) each mow. First mow of the year, my batteries were a bit sleepy (as I expected). I got 90-95% through my mow and the blades cut out. I am in SE WI and store the mower on the charger in the back of an insulated garage. I am guessing it will be better after a few spring mows (also it was 45 degrees out, so that may have cut the mow short as well). In the first 2 seasons, I never got below 4 bars on the mower when mowing the full lawn.

Eric SMember since Sep 2021

Batteries are back in the mower as of today.  As previously noted I’m keeping an individual 4amp charger on each battery.  After each use I’ll plug in each pigtail and be able to charge/maintain independently.  I’m using four, 4ah Viking charger/maintainers purchased at Harbor Freight.

jamisMember since Apr 2010

My 57 month old, 75 ahr. mower has 228 uses, 152 hours, 2,083 charge cycles, and a lifetime routine Depth Of Discharge of 10.23%. My last mow only made it 32 minutes to deck motor shutdown. I haven’t tested the original batteries yet, but I’ll bet one is beginning to be unable to hold a charge under load. I used it today to haul 7 cu.ft. carts full of old mulch a mile away for dumping and the six trips only used .2 of a volt and no bars or percentage on the meter. 260 watts to recharge to 53 volts. Monday, I’m going to order four Mighty Max ML100-12 batteries as the mower has now saved enough in gas and maintenance to pay for them.

JeremyAMember since Jul 2021

 

JeremyA wrote:

On 5/1/2023 at 4:24 PM, JeremyA said:

Posting this just for others information…

 

My mower was new in June of 2021 – has 60 hours on it and I mow 1.25 acres (90ish minutes) each mow. First mow of the year, my batteries were a bit sleepy (as I expected). I got 90-95% through my mow and the blades cut out. I am in SE WI and store the mower on the charger in the back of an insulated garage. I am guessing it will be better after a few spring mows (also it was 45 degrees out, so that may have cut the mow short as well). In the first 2 seasons, I never got below 4 bars on the mower when mowing the full lawn.

 Second mow was much better yesterday – was 75 degrees, made it through the whole lawn with no shutdown and 4 bars left on the BLM when complete. Voltage on the mow went from 54.3 to 50.9.

Eric SMember since Sep 2021

2nd mow in two weeks, each time meter dropped one bar.  Grass has been dry and I’m leaving the cut at the highest level possible on the deck, 4”.  Since I don’t have an irrigation system in the yard I keep it cut high and let nature take its course.  

jamisMember since Apr 2010

The four Mighty Max ML100-12 batteries arrived on 05/11/2023. I checked the voltages on all. They varied between 12.63 and 12.73 volts. I ran two charge cycles on each, one on deep cycle and one on normal automatic. Then I installed them. Charged voltages were all within a tenth of a volt. It took about 3 1/2 hours, start to finish. No issues, nor modifications to the tray. I did add some additional foam padding between the batteries and between the battery ends and the adjustable stops. The performance is better than the 75 ahr. batteries and the cost per hour is dropping, as is the DOD. In hindsight, I wish I had spent the extra $200 for a RM480ex when I bought the mower five years ago. The first mow was heavy cutting and lasted an hour, no bars, 100% left on the meter, 1.9 volts used, and 1860 watts used to recharge. My neighbor is friends with some ham radio operators and one of them is taking the old Leoch LPC12-75 batteries to use as a battery backup setup with his solar array for his radio.

jamisMember since Apr 2010

Had a good operational cost comparison yesterday. Neighbor behind me has a 42″ Toro Timecutter 0turn and the neighbor next door has a Gravely 34″ 0turn. All of our lawns are 10,000 sq.ft. and we all spend about a half hour mowing. The V-twin ICE engines in the Toro & Gravely burn a gallon of gas an hour when mowing. 87E10 here is $3.69/ga., so the neighbors spend a $1.85 to mow their lawns. $1.85 likely isn’t a big expense to mow your lawn and folks likely don’t look at what it costs to run a lawn mower. My RM480 costs $0.06 @ my electric rate to mow the same sized lawn. Add in the cost of maintenance for an ICE mower that the RM480 doesn’t have, and it’s easy to see why my RM480 saved enough in 54 months to pay for a new set of 100 ahr. batteries.  Oh yeah, the Toro cost $3,400 new and the Gravely cost $7,995 new. I paid $2,499 for my RM480e new.

fm2176Member since Feb 2017

jamis wrote:

1 hour ago, jamis said:

Had a good operational cost comparison yesterday. Neighbor behind me has a 42″ Toro Timecutter 0turn and the neighbor next door has a Gravely 34″ 0turn. All of our lawns are 10,000 sq.ft. and we all spend about a half hour mowing. The V-twin ICE engines in the Toro & Gravely burn a gallon of gas an hour when mowing. 87E10 here is $3.69/ga., so the neighbors spend a $1.85 to mow their lawns. $1.85 likely isn’t a big expense to mow your lawn and folks likely don’t look at what it costs to run a lawn mower. My RM480 costs $0.06 @ my electric rate to mow the same sized lawn. Add in the cost of maintenance for an ICE mower that the RM480 doesn’t have, and it’s easy to see why my RM480 saved enough in 54 months to pay for a new set of 100 ahr. batteries.  Oh yeah, the Toro cost $3,400 new and the Gravely cost $7,995 new. I paid $2,499 for my RM480e new.

 

Good to hear.  I considered the EGO ZTR but when my neighbor hooked me up with a deal on a Bad Boy with 14 hours on it, I couldn’t help myself.  I think that the battle between internal combustion (IC) and electric mowers will be going on for the indefinite future.  While I like my battery powered OPE and power tools I know that what they lack in maintenance requirements is offset to an extent by their reliance on relatively slow charging and ever-depleting batteries.  In other words, with gas I can expect to change the oil, spark plug, and filters annually, and need to keep a can of gas on hand.  If I run out of gas, it’s a quick trip to the station for more.  With battery operated equipment/tools, maintenance is almost nil, but if my battery dies, I forgot to charge it, or if it’s stolen or misplaced, I’m out of luck.  Maybe a trip to Home Depot to spend hundreds on a replacement is possible, but odds are I’m not getting the job done soon.  

 

 

jamisMember since Apr 2010

Electric tools require a different perspective than gas platforms. When I started with cordless tools, I learned that multiple batteries and chargers are a necessity. In the nineties, I had two chargers and six batteries. Now with lithium, I’m down to five batteries and a single rapid charger. My OPE is 40 volts and I have seven batteries (3-4 ahr., 2-6 ahr. & 2-7.5 ahr.) and two fan cooled rapid chargers. With that arrangement, I can run things non-stop. It costs $0.02 to charge a 7.5 ahr. battery and two of them will run the snowblower for an hour and half. The rapid chargers charge at the rate of an ahr. every 10 minutes, so you need to plan pack usage if you want to run non- stop. My first 18 volt lithium pack lasted 13 years in regular usage with the other packs.

fm2176Member since Feb 2017

They definitely require a different perspective, and strategic usage of battery-operated equipment can have benefits that gas will never get.  Less heat and noise, no emissions, instant start, etc.  My five-year-old EGO string trimmer is great.  My neighbor has a professional-quality Echo gas trimmer he bought about 15 years ago.  It’s been maintained and has gone to the shop once or twice for repair, and wouldn’t you know, just a couple of weeks ago it had to go back.  I can’t say how well the EGO will be doing in 10 years, but I put it away dirty and haven’t done anything besides replace the trimmer line.

 

I have multiple batteries and chargers, for multiple brands and voltages.  Bosch 18v; MetaboHPT 18v; DeWalt 8v, 12v, 20v, and Flexvolt; Milwaukee M12 and M18, Ryobi One+; and Ridgid 18v, along with the previously mentioned EGO equipment.  If I would have gone electric for my ZTR I’d have probably coughed up the price for the EGO.  

Eric SMember since Sep 2021

Removed the four, 4ah Viking charger quick connect cables from the batteries this past weekend.  Chargers were definitely working but taking longer than I wanted to charge up the batteries, which was to be expected.  I’m mowing about every 4-5 days, still cutting at the tallest deck height.  I switched back to the original charger that came with the mower.  I think I’ll just use the individual battery chargers again next winter when I remove the batteries from the mower and put them in the basement.  

JoeFMember since Oct 2022

FYI – ever since I replaced the OEM 75Ah batteries with the mighty max 100Ah batteries, the battery level meter has only ever reset back to 100% (after a charge) maybe two or three times.

Before the battery swap, I used to get the occasional bug where it would not reset, every once in a while, and could just turn the key off or plug the charging cable back in for a second and try again, to resolve the issue, but now it seems to be the new norm. So instead I now just use the button mod to keep an eye on the voltage and get a general idea of how much charge remains.

jamisMember since Apr 2010

Six mows after replacing the original Leoch 75 ahr. batteries with the Mighty Max 100 ahr. batteries and no issues at all. Charger and BLM operate as they always have, even with the button mod. BLM bars are all on after a charge, but all mows are less than 10%. It’s drought conditions here right now and mowing is very light. Biggest change is the Depth Of Discharge. OEM lifetime average DOD was 10.18% (my average usage was 42 minutes). The DOD with the MM is currently 7.08%. Lower routine DOD translates to longer lifespans in SLA/AGM batteries. I wish I had spent the extra $200 for the RM480ex when I bought the mower 58 months ago. Speaking of $$$, if you are interested in Mighty Max replacement batteries, contact MM directly. 

Eric SMember since Sep 2021

This past Thursday I started with 100% charge but at abound the 45 minute mark the charge meter dropped to 70%, then 50% at 1 hour, then 40% at 1 hour and 5 minutes of use.  I did notice quite a bit of dried grass build up around the blade motor covers which may have been the problem, not sure.  This was the fourth or fifth time mowing using the Mighty Max 100ah batteries I bought last year in May.  As most of you know I kept the batteries inside in the basement this past winter.  Each battery was on its own individual 4amp charger/maintainer for nearly 7 straight months.  Mower has been plugged in since Thursday after it reached 40%.  As a side note the blades were shutting off at 40% which I assume was due to the heat/lack of airflow due to dried grass being buildup around the motor covers.  Fingers crossed that I didn’t get a bad battery from Mighty Max.  I’m using the original charger, and it only took about 3 hours to bring the batteries back to 100% full charge as per the meter.

jamisMember since Apr 2010

When I have finished mowing, I use my 190 mph Ryobi leaf blower to blow off the deck. I blow directly into the deck motors and I also remove the battery cover under the seat and blow down around all of of spaces inside the covers. When I pulled the battery tray to replace the OEM batteries, there was almost no detris inside the mower. 

You are the influencer. Post it to 4.4 million followers.

Hit record. We’ll handle the rest.

Upload your review