PaulNY wrote:
On 6/7/2020 at 8:37 AM, PaulNY said:Hello,
I have a Ryobi ZT480e that I bought last year. It s a fantastic mower and well worth the price. In the first year I more than paid for it in comparison to what I paid a landscaping company the year before.
Almost from the beginning I have had an issue with the battery. Note: I fully charged it before I used it the first time. I mow once a week and keep the mower plugged in whenever it is not in use. When I get ready to mow, I check the battery level. Since it has been charging all week, it should be at 100%. This isn’t the case. The battery will show 70% charge. I discovered if I unplugged it. waited a minute, and then plugged it back in for 10 minutes the battery would then show 100% charge. I called Ryobi about the problem, but their response was that it shouldn’t be happening and the representative I spoke with did not believe me. She stated they had never heard of the problem before.
I mow roughly 3 1/2-4 acres. I have to do it with two charges. I will mow in the morning. Plug in the mower for a few hours and then mow in the afternoon. I have been using the battery down to 10% on the morning mow (I now realize I should not do this as I read the article from mycountryacre.com about not taking the battery down to less than 20%).
Anyone else have a similar issue with the batteries or have suggestions? Thanks for your input.
Hey PaulNY! I’m having the same issue with the 70%. I found my way hear searching if this was an issue anyone else was having. I haven’t tried calling Ryobi yet.
soonerjim wrote:
On 8/29/2020 at 10:53 PM, soonerjim said:Hey PaulNY! I’m having the same issue with the 70%. I found my way hear searching if this was an issue anyone else was having. I haven’t tried calling Ryobi yet.
The instrumentation on the Ryobi’s is known to be variably inaccurate. The ZT480s have been described by many as not reporting the charge % accurately. Some users have even had the meters replaced under warranty with no improvement. Based on my experience and from working with Ryobi support, the first thing I would do is fully charge the battery pack to when the charging lights on the charger and the mower glow steady green. Then measure the pack voltage at the bottom two contacts of the charging port. Voltage should be 51 – 52 volts. Then turn the key on and turn on the headlights. Now measure the voltage again. If it has dropped a lot (the system shuts down when the voltage drops below 36 volts), you likely have a weak or failed battery (I.e. won’t sustain a load). Ryobi’s procedure is to fully charge all four batteries and put a load test on each to determine if one or more have failed. Many people have replaced all four batteries because they didn’t test them individually. I took mine to a local battery shop for load testing and they found one to be failing. After replacement, the mower runs better than when new.
Hey, All:
Commenting on several points presented in related posts:
1. I see the same 70% charge on my Ryobi mower if leaving it on the charger for more than 48 hours. If simply charged overnight, it displays 100%.
2. Regardless of what the display indicates (70% or 100%), I seldom get more than 45 minutes of run-time from it. Sometimes I might get an hour from a “100%” charge, depending on how tall the grass is.
3. Regarding replacement batteries, I did try replacing the OEM batteries with LiFePO4. A four-pack of those would work great and provide extended run-time, but the mower’s controller won’t let the machine start with voltage exceeding 52.5V. The LFP battery pack reaches 54.5 after a full charge, but that exceeds the controller specifications and it won’t turn on. Similarly, the controller is tuned to turn off the blades at 48v and allow enough remaining power to get the mower back to the barn. However with LFP batteries the controller shuts down the blades AND the drive motors simultaneously.
4. I get the ‘wheel-squeak’ that someone posted in a different thread; first from the left-rear (a few months ago) and now from both. I’m not aware of any way to grease or diagnose those drive motors, but I suspect some fault or wear condition is contributing to the very low runtime.
Thanks!
USMC Mustang: Great reply and I have a couple of questions if I may.
Item #2: The reduced run time seems to be the most common complaint for the ZT480s. Have you done the Ryobi recommended battery test of load testing each battery individually? I was experiencing increased Battery Level Meter bars out on my RM480 in the first year of use. Ryobi had me individually charge each battery and then load test them (took them to a local battery shop for the test). One didn’t past muster and was replaced. Mower ran (and still runs) better than new.
Item#3: I’m extremely interested in the lithium batteries you used. I’ve heard several people wanting to try the change, but you are the first I’ve heard of to do so. What make, model, voltage, ahr, etc. I have seen my OEM pack at 52.2 volts immediately after completing a charge, and it ran fine. Ryobi also told me the system shuts down completely when the pack voltage drops below 36 volts, but I’m not sure how the system is really measuring things as the BLM does not read reliably by volts, so the controllers must be measuring something in addition. The system is supposed to shut the blade motors off with enough charge to let you drive back to the charger. I run with a separate volt meter plugged into the charging port so I can see dynamically the charge being used. I would guess the lithium chemistry behaves differently enough to “fool” the electronics that are designed for the SLA/AGM chemistry. How did you charge the lithium batteries? With the Ryobi charger and onboard controller, or a separate charger?
Item #4: First I’ve heard of the squeaky rear bearings on a ZT480, best advice is to call Ryobi at the toll free number on the label under the seat with the model number, serial number, and manufacturer number from the label also. I wonder if it’s the brakes?
jamis wrote:
On 3/19/2020 at 11:58 PM, jamis said:Sorry for the late reply, but the snow plow is back in stock at HD for $329 and free shipping. The manufacturer made a change to the plow lift handle to make it easier to raise/lower the blade without having to get up off of the seat and stopping the unit. Don’t know about moving dirt, but it should work with loose dirt. I wouldn’t use it like a bull dozer to break compacted ground.
Thanks for the reply. I did get one from Niagara Falls N.Y. soon after I made the inquiry here. At the time there were some available in the U.S., so I order it through Home Depot online, drove across the border to pick it up, paid the Canadian taxes and after currency conversion it is cheaper than buying it from Home Depot Canada. The snow plow works really well, and I highly recommend it.
I also run into the battery charging problem, in that I not knowingly let the voltage drop too low (the outlet I plugged it into had no power) and the charger just wouldn’t charge it. I took the battery out and charged them one by one and put them back in, and it all fine now.
I have another issue now and I wonder if anybody has any suggestion. The right hand side cutter motor would cut out whenever the grass is a little too thick (not very thick, just a little thick), but the left side is fine. The motor looks fine physically, inside and out.
LX8: if the grass being cut is rather tall, there can be build up under the deck and cause the right blade to stall. Rather easy to do if you are mulch mowing. If you pay attention to the motor noise, you can hear the motor change pitch due to the loading.
At some point over the winter the gfci I have this plugged in to tripped and the charger stopped charging allowing the batteries to die. I just reset the gfci (outlet is definitely working) but the light on the charger isn’t going on, neither is the light by the charge port on the mower.
Has the charger somehow failed by not having power? It was working fine 3 months ago, I have no idea when the gfci tripped, but long enough ago for the batteries to completely drain.
Is there some way to reset the charger? I’ve had it less than a year, if the charger is the problem (it’s possible the charger is what caused the gfci to trip, although I don’t know why it would after it being used fine for 6 months) will it be replaced under warranty?
Thanks for any help you can offer
Sorry for the late reply, but I don’t visit here often. The charger won’t charge if the battery pack has dropped below 36 volts. Ryobi’s troubleshooting process is to disconnect the battery wiring and individually charge the batteries with an automotive style charger, reconnect the battery wiring, and try the charge process. If the batteries still won’t charge with the automotive charger, the batteries may be toast as SLA/AGM batteries don’t take well to being completely discharged. A Load test of the batteries by a battery shop will confirm the state of the batteries. A call to Ryobi support should be done.
I am contemplating buying the Ryobi mower. They range from $2399 – $2999 from HD. They start at 50AH to 75AH to 100 AH battery. If I buy a 50 or 75 AH model and later find I want 100 AH is it simply a matter of buying the higher capacity battery or are there other considerations between the models?
The 50 ahr model can only have those batteries due to the design of the battery compartment. The 75 ahr and 100 ahr models (both rear engine and zero turn versions) have identical battery trays and can be upgraded to the larger batteries. The 100 ahr batteries are physically larger than the 75 ahr batteries, but there are movable and removable spacers in the tray to accommodate the different sized batteries. Be aware the batteries should last for 1,500 – 1,700 charge cycles, so you might want to consider spending the extra $200 up front to get the longer run time.
Does anyone know where I can replacement 100 ahr batteries in Canada. I looked and looked and couldn’t find any anywhere
Google “Leoch LPC12-100 battery”. I have found some online from battery supply shops. Leoch has a new line out. The LDC12- models are direct replacements for the LPC12- models and are in the same case sizes. The difference is the LDC12- models have longer life spans. In the Ryobi mowers, the LPC12- batteries should deliver 1,500 – 1,700 charges, while the LDC12- models are good for over 2,000 charges. Have you done the Ryobi battery test yet? You remove the batteries from the mower, disconnect the wiring, individually charge the batteries with an automotive charger, and load test each battery. I took mine to a local battery shop for the load test. Only one battery needed replacement and the mower ran better than when it was new.
By the way, Ryobi just brought out a 54″ zero turn mower powered by 115 ahr. batteries.
Hey everyone. Long story short, I bought my zero turn last year. The very first time I took it out, the back right wheel locked up. I looked up video on how to fix this, but being that we use electric vs gas, none of the issues I found were similar to mine. I called HD and Ryobi, and neither knew what to do. Anyone have any ideas? Thanks for the help!
wait a minute? Ryobi had no help for a product under warranty? Call back and ask for an electric rider specialist. Have your model number, manufacturer number, and serial number from the label under the seat available. Can you push the mower by hand or is it completely locked up? Does everything else work, headlights, mowing blades, the high/low speed button?
I haven’t found any reported issues like this. I’m going to suggest some SWAGs to try, but no assurances.
1. Try disconnecting the master fuseable link under the seat that connects the battery pack to the mower for a minute. The plug it back in.
2. If all other things work, make sure the parking brake is fully released.
3. The right control lever mechanism and wiring should be inspected for broken or frayed wiring. This may require assistance from Ryobi.
4. Can you rock the mower forwards and backwards to see if it frees up the stuck drive? I know of one user who had an issue like this and his mower went off to a service center, but he never updated any resolution.
5. Again, does changing the low speed drive button have any effect?
6. Can you check the battery pack voltage at the master plug? It should be above 50 volts. Voltage should be around 52 volts when the charging cycle is complete. The system will run until the pack voltage drops to 36 volts and then the system shuts down to protect the SLA/AGM batteries.
7. In any event, call Ryobi at the number listed on the under seat label and don’t take “I don’t know” for an answer.
8. One last suggestion, go to the HD web page for your mower and open a new question with your problem. You might get an answer from another owner and the Ryobi rep there may respond also.
Hope this helps
Early on with my RM480e, the charger was displaying a low voltage code. My call to Ryobi customer service was immediately diagnosed as a failed charger. A new charger was overnighted to me. It displayed the same low voltage error. A second call to Ryobi support finally got me connected to a riding mower specialist. Turned out my original charger was fine, the replacement charger was the wrong one and should never be used with my model mower. The problem turned out to be a failing battery, but Ryobi’s first line of support was not able to properly diagnose my problem.
Hello,
2019 bought Ryobi 480e, 1.5 years use, 1/4 acre, stored in basement all winter plugged in except when power would go out, poor infrastructure, When tried to start last week, it Would not start, no reaction when turning the key, charger light and mower charge port not blinking, one battery would only charge up to about 6V using standard 12V charger after unhooking all batteries. Other three charge over 11V Installed new battery same specs except 80 amp instead of original 75 amp, strict compliance with utube instructor, well versed and competent.
After install, hooked up all connections plugged into factory charger, light on charger and mower blinking, turn key nothing…..no head lights no buzzer when off seat, nothing. Key no noise click when turning, no resistance, just smooth going from aux to off to on. Last year I had bent the key a little getting off the mower, but didn’t seem to matter at the time, continued use for the summer.
Please help if you can.
Thanks,
Phillip
Ryobi specifies using only the Leoch LPC12-75 batteries in these mowers. The charger is specially set up Delta-Q SC-48 charger for these batteries. What was the blink code the charger was displaying? The mower will not run if the charger is plugged in. The system will not run if the battery pack voltage is less than 36 volts. The batteries should charge to 13.2 volts max. when properly charges. The pack voltage of my 33 month mower is usually 52.4 volts right after charging. Call Ryobi for help. The mower is warranted for 3 years even if the batteries are only warranted for a year.
I also had an issue with the outlet losing power over the winter and am in the process of doing the recommended recharge of the batteries individually. As they finish charging, I’m trying to test them with a Foxwell battery analyzer. Does anyone know what the Cold Cranking Amps or Resistance should be? I am seeing 330 CCA and 7.74 MR.
jefe: how long was the power out? Long enough to drop the pack voltage below 36 volts? The Ryobi system will not charge the pack if it falls below 36 volts. Leoch states these batteries can self discharge for up to six months before needing a maintenance charge. What is the individual battery voltage right off the charger? Should be at least 13.2 volts by my experience. Which LPC12 battery, 75 ahr or 100 ahr? Leoch doesn’t state CCAs. Google “leoch lpc12-75.pdf” or “leoch lpc12-100.pdf” to see their data sheet. Ryobi only advised me to load test them, which I did by taking them to a local battery shop. They tested all four of them for free.
Thanks Jamis. I have the 75 ahr batteries. I’m not sure when it lost power, but probably was out for a month or two. When I unhooked them and pulled the tray out, each one was at about 6 volts so definitely was below 36 volts. I’ve individually charged them and they are all back up around 13 volts. I did find the leoch data sheets online and wasn’t able to glean anything useful to use as a standard in my at home tester. Guess I’ll have to take them to a battery shop.
A load test is definitely in order, just to see if any were damaged. I had one battery fail at 11 months and it wouldn’t support any sort of load, even though it would take a charge albeit very slowly compared to the others. The Ryobi charger would not charge the pack and displayed a low voltage error (2 red blinks on the charger LED). The replacement battery made the mower run better than new which told me the failed battery was weak from the first run. Good luck
jamis wrote:
On 7/29/2020 at 7:15 PM, jamis said:The instrumentation on the ZT480s (and the RM480s) has been reported by many to be inaccurate and misleading. The Battery Level Meter on my mower is erratic in its reporting and the hour meter is off by 6%. The hour meter even reset itself to zero last summer. I do some extra steps to monitor the battery performance so I know how healthy the pack is.
1. I measure the pack voltage before and after mowing. I use a volt meter to read the voltage at the charging port.
2. I bought a $30 recording watt meter to measure how much it takes to recharge the pack each time the charger does a charge.
3. May be extreme, but I put this all into a spreadsheet to track usage trends.Ryobi’s battery check method is to pull the batteries, disconnect all pack wiring, charge each battery individually with a separate charger, and load test each. I took mine to a local battery shop for the testing.
Boost charging is NOT recommended for SLA batteries as it can promote sulfication in the cells and shorten battery life. Always fully charge the pack when you charge the mower. Reduced run time is usually due to one of the four batteries having a weak cell. Eventually, the battery will fail entirely and the system will then refuse to charge the pack. The electronics limit battery drain down to 36 volts to prolong the life span of the pack.
How do you check voltage from the charging port? It looks like you made a custom cable… but can you do this with just a multimeter? (And where did you get that spare connector from?!?) If so, which pins do you use on the charging port?
Kage825 wrote:
17 hours ago, Kage825 said:How do you check voltage from the charging port? It looks like you made a custom cable… but can you do this with just a multimeter? (And where did you get that spare connector from?!?) If so, which pins do you use on the charging port?
The bottom two contacts are the + & – of the system. The top contact is the battery temperature lead to the charger. I used a multimeter for quite some time. The spare charger plug is from a charger Ryobi sent me when I had a failing battery. The first support person I talked to said it was a bad charger with no troubleshooting. The charger they sent me was the wrong p/n and I was told not to use it, and not to return it either. The plug and cord were then available to use with the voltmeter.
wolfie99 wrote:
On 3/16/2021 at 6:14 PM, wolfie99 said:Does anyone know where I can replacement 100 ahr batteries in Canada. I looked and looked and couldn’t find any anywhere
I just found a place called Total Battery. Since I live in Gatineau, Quebec, I spoke with the Ottawa store. They are getting some 80ah batteries in about a week, and 100ah batteries by the end of June, he said. Price was the best I have seen so far for these: $266.76 for the 100ah and $233.51 for the 80ah ones.
Very curious as to exactly what brand and model batteries the store is supplying. The reason I ask is Ryobi specifies only the Leoch LPC12 batteries are to be used in these mowers because the SC-48 charger is set up for them. I have only heard of one user that has used a different brand of battery, but has not shared his results yet. The batteries he used have about half the stated charge cycles of the Leoch batteries and they were more expensive than the LPC12s. I look forward to see your results.
I have encountered an issue with my rm480e mower. I was checking the voltage at the charging port yesterday and while I had my meter connected to the charging port with alligator clips I turned on the key to see if there was a voltage drop, and then turned it off immediately.
Well I guess the lockout to prevent the mower from turning on while charging must have kicked in because even though I
have removed my meter the mower is totally dead. Turning on the key does nothing and there is zero voltage at the
charging port. What do I need to do to reset my mower? Anyone got any ideas?
Thanks, John
(I have not been in touch with Ryobi yet and am not too sure the warranty would cover user stupidity (if I am to blame))
Thanks Jamis, that’s good to know, and I appreciate your suggestion re the fuse.
Turns out it is the Charger Receptacle which has failed. The power wire to the blue connector is open (the live side of the blue connector reads 52.4volts). I guess there must be some electronics hidden beneath the layer where the wires attach to the back of the receptacle. Not much chance of getting under there to fix anything.
I ended up contacting Ryobi and they have ordered a receptacle for me, but it is on back-order so who knows how long I will be waiting.
Do you have the Repair Sheets document downloaded? It is available on the Ryobi web site pages for your mower as a .pdf file. Sounds like the batteries are fully charged though.
Hey Jim,
The fellow from the help desk emailed me a Ryobi Riding Mower Repair pdf which is a 55 page electrical component
troubleshooting guide for the mower. Is that what you were referring to? Funnily enough the problem I found was not
in their document.
Yes the batteries were fully charged before the receptacle failure.
I heated up the black layer and was able to remove it from the receptacle so will see if I can fix the board once I get it removed. It is held in place with tamper-resistant screws of all things, so I had to buy a special tool.
The .pdf I have from the Ryobi web site is only 29 pages. Would love to see what they sent you. What is the name of the person that has been helping you?
Would you be willing to email the .pdf to me if I send you my email address? Would you be so kind to post a picture of the failed area?
Just found this forum as I have a ryobi 54” ztr mower and would like to add some lights to it. Is there an electrical diagram to be had? I’ve thought about just connecting to one of the 4 batteries, but would like to understand the overall system a little first. I wonder what he existing LED lights are connected to. I’ve not started disassembling, was hoping for a document. How do you get a Repair pdf?
thanks, Kurt
The repair sheet .pdf is downloadable from the Ryobi web site page for your model. it isn’t really detailed enough for what you want though, just exploded parts diagrams and part numbers. My neighbor tapped into his RM480ex system by buying the connectors for the main battery connectors off the internet and then using the “48” volt current to power things like a high mount LED headlight and other accessories. He added a module to step the 48 volts down to 12 volts. This way no modification to the Ryobi system and it can all be easily removed. His mower will soon be out of warranty, so he’s not concerned. These systems have a 12 volt controller, but it’s not tappable that I know of and I don’t really know what it’s used for in the system.
Hi Jim. Sure send me your email. I can send you the manual for sure. Where is the downloadable one located on the Ryobi website?
Breischaft wrote:
On 6/13/2021 at 8:55 AM, Breischaft said:Just found this forum as I have a ryobi 54” ztr mower and would like to add some lights to it. Is there an electrical diagram to be had? I’ve thought about just connecting to one of the 4 batteries, but would like to understand the overall system a little first. I wonder what he existing LED lights are connected to. I’ve not started disassembling, was hoping for a document. How do you get a Repair pdf?
thanks, Kurt
Thanks to John31224, I have just learned that the headlights on the RM480s are 12 volt powered, so the 48 volt DC to 12 volt DC converter on the mower is what is used for driving the headlights, backup beeper and the USB port. Yes, the USB port delivers 5 volts, but it is driven by 12 volts. I would expect the ZT540 to be set up the same way. Disconnect one of the headlights at the connector by the mount and measure the voltage with a digital meter with the mower switched on and the headlight switch depressed.
Next question: intermittently, I cannot get the mower to move. I push the ztr levers forward, no motion and it beeps. ‘Feels like’ an interlock is not being met. I pulled the seat switch and clamped it, thought that was it. Next time, it happened when went over a rough part of yard. Pushed it around and finally got going again but unsure why. Seat occupied, brake off, levers in, ???
Ideas?
1. When it won’t move forward, will it move in reverse?
2. Problem is with both levers?
3. What happens if the levers are moved out and back in? Required to reset the system after turning the key to on.
4. Any difference in high or low speed settings?
5. Beeping is most likely due to the seat safety switch not being triggered by the operator’s weight.
5. Call the Ryobi support number on the label under the seat and have all of the other numbers available for the support person.
Does not move in either direction with either lever. Hi/low no matter. Seat switch physically removed from seat and clamped, so it’s not it (unless there’s an intermittent open somewhere)
tell me the system reset detail please? At one point, we were convinced that removing and reinserting the key was the ticket, but no. Is there a combination lock between the levers and the key with a sequence?
ryobi support has been long hold and work hasn’t been that flexible – plus mower at home
appreciate your knowledge
According to the manual, turn the key off, open the levers, turn the key on, and close the levers in neutral position. The beeping gives me pause. Not sure what you mean by clamped off, but I wonder if the switch has become defective somehow. My neighbor had issue with his as it kept popping out of the latched position. I have the seat switch test procedure on my PC and I’ll look it up later. I wonder if the parking brake switch is amuck and causing the problem.
Kurt: PM’d you with some troubleshooting documentation. Don’t know if I should make it public, hence the PM. Hoping it might help.
Clamped means I first thought the seat switch was not being made. So I removed it from the seat and clamped it in the depressed position. Doesn’t eliminate if it’s defective completely, but…
Another thought I have is that it may need to be opened and then closed again to reset whatever circuit logic that is kicking in
The 12 beeps is confounding since it’s not documented in the manual. If it beeps exactly 12 times each time, that’s a real question for Ryobi to address. The testing procedure listed in the troubleshooting manual should be the same for the ZTs.
Called and talked to them. Of course, mower not doing this at time, but knowledgeable service.
Told me immediately that 12 meant bad connection to main drive and that’s where I should look. If it continues and the wires are secure, they can send another drive for me to swap.
I asked and he said he could send me the troubleshooting guide, which I got. PM me if you’d like. Agree with your comment: 12 beeps not on the list.
Again super thanks to you, Jim. I’d have never even counted the beeps before you asking about it.
Will update here as things progress.
If both levers are not working, I’m wondering if it’s the drive as there are two, one for each rear wheel? I wonder if it’s something feeding both controllers? Maybe the troubleshooting manual will offer a process to check the power feed to the control lever mechanisms? Just SWAGing here.
my lack of attention to detail: only beeps when left lever pushed or pulled, leading to the main drive not the slave.
One step at a time. I didn’t realize early on how complex these machines are. The troubleshooting manuals are so worthwhile.
I was clued into a YouTube video by member John31224 that covers a modification to the RM480 display module that allows the meter to switch through the three modes of display, Volts, Percentage of Charge, and Hours Run. The video is found by googling “Ryobi 480e riding mower battery indicator mod”. It is a simple and inexpensive addition and makes operating the mower more informative. It adds a momentary push button to the console. Mine mounted in the seventh bolt hole between the key switch and the meter. The video shows the three displays.





