Ryobi battery riding lawn mower

Eric SMember since Sep 2021

Just finished load testing all 4 original batteries about 10 minutes ago, 2 batteries were bad and the other 2 batteries were on the line weak/good.  I load tested each battery twice, both times same results.  
 

As you guys have read through the posts I had a feeling at least one was going bad last year but pushed through until fall when I was done mowing.

 

 Just notified by HD the Mighty Max 100ah batteries are supposed to be ready for pick up tomorrow.  I bought 4, glad I did.  

 

I left everything disconnected so it should be a quick hookup.  I’m going to plug it in over night and get them all changed up.  
 

btw:  I did mow this morning with 100% charge as per mower battery level meter but it only lasted 30 minutes until the blades stopped and I was on 30%.  

jamisMember since Apr 2010

My neighbor with a RM480ex just received his replacement Leoch LPC12-100 battery from HD. He load tested all four and only one failed. Won’t be installed until this weekend. The new battery is on a charger to make sure it’s up to full charge before assembling into the pack. This was Ryobi’s advice when I had to replace a battery under warranty.

jamisMember since Apr 2010

I think my batteries have fully recovered from winter storage. My RM48oe is 45 months old, 177  mowings, 336 charge cycles, and 120 hours of run time. Today, I mowed 26,000 sq. ft. (.6 acre) of lawn non-stop for an hour and a half, ( lots of turns). The run used 3.4 volts and 58% of the usable charge and 6 bars on the BLM. The spring grass was pretty dense as the run used an average of 60 amps. and it took 3,030 watts ($0.36) to fully recharge the battery pack. This is inline with previous 1.5 hr. runs from the previous seasons. I think the batteries would have easily hit the 2 hr. run time specified for this mower. If fact, last year, I got a 2.5 hr. run from this set of batteries. It still costs less than $0.26/hr. to run. Compare that to $4.25/gal. 87E10.

SuperDave733Member since May 2022

Hey, I’ve got a technical battery question that you might have an answer to. 

 

I have a 42 in. 75 Ah Battery Electric Riding Zero Turn Mower that I want to upgrade the battery to a lithium varient.

as you probably already know the current battery(s) are: 12v 75Ah lead acid batteries x4.

I’m looking to upgrade to a lithium battery 14.4v 100Ah (max charge 50A) x4.

The wall charger outputs 48v 13A. 

So if I were to replace the lead acid with the lithium, in theory it should (hopefully) work with my mower and/or the mower’s computer?

jamisMember since Apr 2010

SuperDave733 wrote:

2 hours ago, SuperDave733 said:

Hey, I’ve got a technical battery question that you might have an answer to. 

 

I have a 42 in. 75 Ah Battery Electric Riding Zero Turn Mower that I want to upgrade the battery to a lithium varient.

as you probably already know the current battery(s) are: 12v 75Ah lead acid batteries x4.

I’m looking to upgrade to a lithium battery 14.4v 100Ah (max charge 50A) x4.

The wall charger outputs 48v 13A. 

So if I were to replace the lead acid with the lithium, in theory it should (hopefully) work with my mower and/or the mower’s computer?

I have yet to see in print anywhere that the electronics and the charger in the Ryobi SLA/AGM mowers will work with lithium technology. Even Ryobi states they won’t. I have seen someone spending more than $1,700 to convert one of these to work with lithium technology. New controllers and charger, plus batteries.  You could buy two sets of SLA/AGM batteries for that. I have yet to see any lithium packs with more charge cycles than the Leoch LPC12s. Elon Musk has stated the current Tesla lithium packs are good for 1,600 charge cycles (300K-500K miles). Ego states their 56 volt lithium packs are good for 1,000 charges. The Leoch LPC12s are rated for 1,500-1,700 charges the way the Ryobi system manages them. How about selling your current Ryobi zero turn and buying one of the new Ryobi lithium zero turns if you just absolutely have to have to have a lithium powered mower?

jamisMember since Apr 2010

Actually, Delta Q SC-48 smart charger used in these Ryobi systems puts out much more than 48 volts. I have measured over 54 pack volts after charging my RM480e. My neighbor measured just over 61 pack volts on his RM480ex this week when he installed a new LPC12-100 battery to replace one that was failing a load test. 

GartenmeisterMember since May 2022

@SuperDave733 if you want to convert to Lithium you are probably better off checking out this thread.

 

Be prepared, it will be a long read.  In a nutshell it appears that guys are doing it but it is fairly expensive and is an in-depth DIY project that requires fairly advanced skills/knowledge.  I believe that most of the guys build their own batteries…so absolutely not a drop-in solution.

 

sailracerMember since May 2022

Hi all- I just joined these forums for this thread.  I have a 75aH Zero Turn that is 2 years old with 39 hours on it that can no longer finish mowing my ~1.2 acre yard on a single charge.  Since it was new, it often had the 70% full charge problem.  I’ve investigated further after reading this thread.  It appears that the charger fully charges the batteries to 100%, then turns off and never charges or trickle charges them again, so that after a week of sitting before the next mow, the batteries have self discharged a little and the voltage is down.  I checked things with a volt meter this week to confirm.  After sitting for a week on the charger, I turned the mower on and it read 70% and voltage measured 51.6V.  I then plugged it back in for a couple hours and checked again.  This time it was at 100% and measured 52.4V.  I then charged overnight and it was at 100% / 51.3V.  A week of sitting on the charger later- back to 70% <52V.  It appears the charger doesn’t keep the batteries topped up.

 

The Winter behavior I saw seems to suggest it is never trickle charging, not that it just didn’t a low enough threshold to start trickle charging.  When I turned the mower on this Spring after sitting for 3 months (on the charger in a garage that never gets below 40 degrees) it read 40%.  It seems to me charger isn’t behaving the way it is supposed to since Ryobi recommends keeping it connected.

 

As for not being able to complete a full mow, after about 40 minutes when the blades shut off now, if I let the mower sit for 20 minutes, the reading goes from 5% to 40%.  Does this give any clue if maybe it is just a single battery going bad or is it meaningless?

 

What kind of load tester is needed for these deep cycle batteries?  It looks like most battery testers apply a fixed load for a very short amount of time and measure the voltage drop over that time.  Can those meters reliably test a deep cycle?  It seems like their current load could be too high if designed for car stating type batteries and might not give accurate results.  

 

Finally, based on the number of premature failures here it seems like Ryobi should be doing something.  I feel like I was ripped off if I need to replace my batteries after 39 hours of use.  Even at $5 a gallon for gas, the battery cost alone is more than double what my gas mower would have cost me over the same time.  Thats not even counting the cost of electricity or how expensive the mower was. 

 

Jamis- you’ve been providing lots of great info here, but I need to question your statement about Ryobi only allowing 30% discharge on these.  Where did that info come from?   I see this chart from the Leoch datasheet which suggests that a battery only discharged 30% will still have half its capacity left after ~1200 discharge cycles.  It also shows that a fully discharged battery will be at half capacity after less than 300 discharge cycles. 

 

Photo from the original forum

 

I expect Ryobi is allowing much closer to 100% discharge than 30%.  Based on your previous post referencing 34V, I’m guessing you correlated a 30% discharge with a 30% drop in voltage?  I would argue that a 30% discharge is referring to the energy in the battery.  That is, a 30% discharge means you used 30Ah out of the 100Ah available.  The voltage does not go down linearly with the energy as this second chart from the battery datasheet shows: Photo from the original forum

 

Based on this chart I expect the dashed line represents 100% discharge.  When my blades shut off after 40 minutes of mowing, my pack voltage is around ~38V which would suggest from this chart that the battery is pretty much fully discharged.

jamisMember since Apr 2010

The 30% DOD came from Ryobi when I had a battery fail at 11 months. I have my charger plugged into a Poniie P2000 watt meter so I can see when the system charges the system. When the mower was new, it would charge the batteries about 4-5 weeks apart and use 400-600 watts to do the maintenance charge. Last winter (the fourth) it started doing a maintenance charge every day of 100 watts per charge. The system has been doing a charge when the pack voltage drops below 50 volts. Re-plugging a fully charged system will boost the pack voltage somewhat. After 340 charges, I suspect the batteries are getting worn, but I can still mow for 2 hrs before blade shutdown. I confess I still don’t understand how these SLA/AGM batteries really work, despite all of the data collected and battery research I’ve done. I took my batteries to a battery shop for testing since they have a commercial unit. I would guess the issue with the charge returning after sitting speaks to a weak cell in one battery. This is what mine did when the run time dropped off. Eventually, The pack charge would drop below 36 volts and the charger would not even attempt to charge the pack. Load testing showed one battery would not hold a charge under load. As soon as a load was applied to the fully charged battery, voltage would fall off. 

sailracerMember since May 2022

That’s weird the maintenance behavior changed.  Either way, it sounds like the charger doesn’t trickle charge for maintenance but instead looks for a threshold to turn on and top up the batteries at a higher current.  That could explain the 70% problem many people have.  Or maybe a battery with a bad cell causes the pack voltage to drop from 100% reading to 70% reading while on the charger within a week.  Maybe everyone with the 70% problem and the batteries still under warranty should have them tested before warranty runs out and they start degrading faster!

 

Has anyone had luck testing these batteries with a basic battery tester?  Something like this: Amazon.com: LNEX Car Battery Tester , 2.8” LCD Color Screen, 100-2000CCA Fast Accurate 12V Battery Load Tester, Cranking and Charging System Digital Battery Analyzer for Car Truck Motorcycle ATV SUV Boat Yacht : Automotive

 

Edit:  Found this tester for $20 and bought it.  Should be here tomorrow- I’ll report back on how it works.  Amazon.com: KINGBOLEN BM550 6V 12V 24V Car Battery Tester, 100-2000 CCA Voltage Tester 2Ah-220Ah Internal Resistance Tester Accurate Digital Auto Battery Analyzer for Cars Trucks SUV ATV Boats Motorcycles Vehicle : Automotive

jamisMember since Apr 2010

My neighbor with a RM 480ex was experiencing reduced run times this spring and he has at least twice the number of charge cycles my mower has because he mows twice the sq.ft. that I do and he plows snow with it. His mower is a couple of months newer than mine. He replaced one battery last week after testing his batteries with  a $40 100 amp. tester he bought on line. He’s gone this week and I’ll have to wait till he returns to get the exact make & model. BTW, there are now five of these mowers on our street of 16 homes. Two are nearly 4 years old, two are two years old, and one is new this spring. Most assuredly the charging system does not trickle charge. I have read that trickle charging SLA/AGM batteries is bad for their lifespan. I have spent a lot of time on the Battery University website trying to learn about these batteries. The 70% charge issue is just bad instrumentation from what I’ve read. Even a new BLM has not fixed the issue in some cases. A weak cell will indeed bleed down and cause a confusing reading and also more frequent charge cycles. When I individually charged each battery as part of Ryobi’s troubleshooting proceedure, the weak battery took far longer to fully charge. That’s why I went to measuring things externally and using a spreadsheet to track battery performance.

jamisMember since Apr 2010

Some additional thoughts on the RM480 BLM. There are two electrical connections to the meter. After startup, the meter shows the cumulative hours the key switch has been turned on (unless it resets itself to zero). There is a third contact on the BLM that has no wire going to it. If you jumper that contact with a normally open push button switch to one of the other leads, you can step the digital display through volts, % charge, and hours run. Some BLMs have a push button on the underside that will step through the displays.  I have recorded these numbers along with the recharge wattage and the amps. used and the number bars out on the BLM. I have not been able to correlate any of these numbers to figure out what the BLM uses to display the information it shows. The % display and the bars out are roughly equivalent, but volts, watts, and amps. don’t tally out from run to run.  I once ran the charge down to 9% and one bar left. The voltage was 42.2 volts from a beginning voltage of 50.5 volts. Another run showed 8 bars out and 23% charge left with 50.7 volts going down to 46.5 volts. Both of these runs ran until the deck motors shut off. The best I can figure out is the BLM uses time and voltage to calculate what it shows. 

sailracerMember since May 2022

Here’s what I found with the battery tester I linked above.

 

It appears to measure the CCA and determine the health of the battery based solely on that.  It uses the number you give it for a target CCA to tell you the battery state of health.  I’m not sure what the CCA should be for a good Leoch 75Ah battery since that isn’t how deep cycle batteries are spec’d.  Does anyone know what a good vs. bad battery will typically read for CCA?

 

All 4 of my batteries measured between 13.06 and 13.12 V when fully charged and removed from the system.  I got the following for CCA on each


Batt 1: 466A

Batt 2: 474A

Batt 3: 536A

Batt 4: 527A

 

This would seem to suggest two of the batteries (the two towards the back of the mower) are weaker.  Does it mean they are bad, though?

jamisMember since Apr 2010

Do you have a battery shop in town? I took mine to them and they tested them for free. I offered to pay for their time (about 10 min.) to test all four, but they refused as they said it was what they do. They even rolled the tester out to my car and did the test with the batteries in the trunk.

sailracerMember since May 2022

jamis wrote:

16 minutes ago, jamis said:

Do you have a battery shop in town? I took mine to them and they tested them for free. I offered to pay for their time (about 10 min.) to test all four, but they refused as they said it was what they do. They even rolled the tester out to my car and did the test with the batteries in the trunk.


I don’t know, I haven’t looked around.  I don’t really want to, even if they do the testing for free because then I would feel kind of obligated to get a replacement battery through them.  There’s also the possibility they don’t know what they are doing with deep cycle batteries vs. car starting batteries and they tell me I have to replace all 4 of my batteries.  I’d rather do things myself to learn and understand what is going on.  

 

Speaking of which, I just ran another experiment.  I turned the battery pack around so I could connect it to the mower while hanging out the back where I could measure it.  I had my wife engage the blades while I measured the voltage on each battery.  With the pack at 100%, each battery measured about 12.25V under load with the blades running.  I ran the blades longer until the pack reported 70% charge, and all the packs still read around 12.25V.  I continued running the blades until the indicator read 25%, then turned it off and measured the voltages.  Packs 1-3 were all around 12.3 to 12.4V but pack 4 was at 10.2V!  That battery also had a hot spot on the case in one area.  None of the other batteries had any warm spots.  The voltage on that battery gradually crept back up once the load was stopped.  So, that must be the one that is causing the problems.  What’s more, it shows the CCA from the test above is useless for determining the health of a deep cycle battery when it is at 100%.  I retested all 4 batteries with the tester.  All of them were lower than when charged to 100%, but pack 4 was down to 339A.  Pack 1 and 2 were about 405 and pack 3 was at 445.

jamisMember since Apr 2010

You just replicated the same sort of test the local battery shop did with their professional equipment. Their equipment had variable resistance to identify the point where the fail was occurring.  I would say you have identified the one battery in your pack that has a weak cell. I predict it will continue to get weaker until it fails completely with an open cell or a dead short cell, or at least to the point where any load will drop the voltage to the point where the mower system cannot run or charge. I used the local battery shop because I’ve been buying car batteries there for decades (5 year replacement warranty) and they have rebuilt numerous cordless tool battery packs over the years, so I trust them. My neighbor’s load tester displays the voltage of the battery and then shows the dropoff when the fixed resistance is switched in. Their documentation states a good battery should hold voltage for ten seconds.

sailracerMember since May 2022

It seems a little odd that the voltage dropoff was only occurring on my battery once it was discharged well below 100%.  At full charge it looked like everything was fine, even under load.  I don’t know enough about battery design to understand what type of problem may cause that behavior.  It’s like it’s OK at sprinting but has no endurance whereas a good battery can do both

 

I ordered one of the MightyMax batteries as a replacement.  It will be interesting to see if the 70% full charge problem goes away after replacing the bad battery.  If it does, that might be an early indicator of a battery with a weak cell.

jamisMember since Apr 2010

I’m very interested in seeing how the MM battery works with the Leoch units. Now that HD is carrying the LPC12s again, I’d be tempted to buy one of those as a replacement. Interesting that the two batteries only differ by $19 in price.

jamisMember since Apr 2010

I find that the 70% display is so common amongst users reporting the display issue. Why is it always 70% and not some other number? That makes me think it’s a problem with the instrumentation and not always the batteries. Made even more confusing with no explanation from Ryobi other than replacing the meter.

glennfinMember since May 2022

Finally found this thread after hours of exhaustive online research… 

 

Jim, I’ve read through the entire thread and I must say, your posts are gold!

I am grateful that you’ve followed up to date with this valuable information that i couldn’t seem to find anywhere else.

 

I’ve had my ZT480E now for, I believe this is the 5th season of mowing. I believe it’s the 75AH model. ….same battery issues that others have reported, 50% / 70%, can only mow for about 20 mins right now. Mower is always stored in heated garage on the Roybi charger, etc etc.

 

Considering the age of the mower/batteries, I will most likely be replacing the pack very soon.

I understand your advise about individually load testing each battery to find a bad one, but I have to consider the chances of another battery in the pack going bad after not so much time which brings me to my fist hurdle/question…….

 

From the photo you posted, I see you’ve built a wood riser on top of a dolly to help removing the battery tray. Are you able to slide the tray right onto the riser from the mower without having to do any lifting?.. This will be a must for me before I can consider anything else. Any info on that would be greatly appreciated. I have a dolly that would work, with locking wheels.

 

Finally, The current price for Leoch LPC12-100 from HD is $239.20.

The current price for the Mightymax ML100-12 from HD is $185.39

Amazon has the Mightymax ML100-12  w/free shipping (prime) for $179.99

 

Do I take a chance with the Mightymax?… that is a considerable price difference considering 4 batteries. 

 

Glenn

 

 

 

jamisMember since Apr 2010

Glenn: Yes, I built the dolly to be the same height as the tray slide. Ryobi’s advice for not having an adjustable height dolly was vary the height of the tray by adjusting the rear tire pressure to bring the two into alignment. I really don’t know about the MM batteries as I’ve not seen the results of anyone using them with the Ryobi charger. They appear to be very much like the LPC12s though. As for how many batteries to replace, it’s up to the owner. My neighbor has a RM480ex with over 600 hours of run time and he just replaced one battery two weeks ago with an LPC12-100 from HD. He’s been gone on a trip so we haven’t seen what the change has done for his run time yet.

TotalRexMember since May 2022

sailracer wrote:

On 5/22/2022 at 5:05 PM, sailracer said:

Here’s what I found with the battery tester I linked above.

 

It appears to measure the CCA and determine the health of the battery based solely on that.  It uses the number you give it for a target CCA to tell you the battery state of health.  I’m not sure what the CCA should be for a good Leoch 75Ah battery since that isn’t how deep cycle batteries are spec’d.  Does anyone know what a good vs. bad battery will typically read for CCA?

 

All 4 of my batteries measured between 13.06 and 13.12 V when fully charged and removed from the system.  I got the following for CCA on each


Batt 1: 466A

Batt 2: 474A

Batt 3: 536A

Batt 4: 527A

 

This would seem to suggest two of the batteries (the two towards the back of the mower) are weaker.  Does it mean they are bad, though?

 

I am having the issue where the mower shuts down the blades and even stops forward power when moving in forward.   

3 of my batteries rated ~440 and one was only 26.  That is likely my problem.

 

I too wonder what a good CCA rating is.   My mower is 5 years old.  I am debating on how many batteries to replace.  I know at least one.    I am using a car battery charger to recondition one to see of that helps. 

jamisMember since Apr 2010

As to the CCA question, I can only say that Ryobi’s troubleshooting process is to run a load test on the batteries to see what the condition is. The $40 load tester my neighbor bought, and the commercial load tester the local battery shop used, both measured voltage drop under load vs time to determine the health of the batteries. I’m no expert, but if that’s what the manufacturer says is to be done, that’s what I’ll do. I also find it interesting that both Leoch and MM deep discharge style batteries don’t list the CCA of these batteries. I do know the Leoch batteries are used in wind farms, solar arrays, UPS installations, and mobility devices where CCAs are not important. 

jamisMember since Apr 2010

TotalRex wrote:

2 hours ago, TotalRex said:

 

I am having the issue where the mower shuts down the blades and even stops forward power when moving in forward.   

3 of my batteries rated ~440 and one was only 26.  That is likely my problem.

 

I too wonder what a good CCA rating is.   My mower is 5 years old.  I am debating on how many batteries to replace.  I know at least one.    I am using a car battery charger to recondition one to see of that helps. 

What is the pack voltage at the charge port when the mower will not move under its own power? My mower will shut the deck motors off at around 46 +- volts but still move. I’ve never run it down to where the drive motor won’t run though.

glennfinMember since May 2022

jamis wrote:

On 5/24/2022 at 6:11 PM, jamis said:

Thanks for the info Jim… I’ll start by building that dolly riser.

 

jamis wrote:

On 5/24/2022 at 6:11 PM, jamis said:

Glenn: Yes, I built the dolly to be the same height as the tray slide. Ryobi’s advice for not having an adjustable height dolly was vary the height of the tray by adjusting the rear tire pressure to bring the two into alignment. I really don’t know about the MM batteries as I’ve not seen the results of anyone using them with the Ryobi charger. They appear to be very much like the LPC12s though. As for how many batteries to replace, it’s up to the owner. My neighbor has a RM480ex with over 600 hours of run time and he just replaced one battery two weeks ago with an LPC12-100 from HD. He’s been gone on a trip so we haven’t seen what the change has done for his run time yet.

 

jamisMember since Apr 2010

Just some thoughts on the instrumentation of these mowers. After 45 months, 342 charges, 124 hours of use,  I have come to the conclusion that the number of variances in mowing and the discharge characteristics of the batteries makes the meters pretty much inconsistent. Using my spreadsheet data, I grouped all of the runs that used 7 to 9 bars on the BLM. One 8 bar mow of 1.4 hrs required 3,610 watts to recharge. A year later an 8 bar mow of 1.3 hrs. required 3,270 watts. This was the same sq.ft., just 6 min. difference in time. This week a 9 bar mow of 1.6 hrs required 3,330 watts. Last year a 9 bar mow of 1.7 hrs. required 4,050 watts. Again, the same sq.ft. The voltage drop of these runs ranged from 3.6 volts to 8.3 volts. the only thing I have been able to determine from the data is that the average cost per use has been increasing by about $0.02 each year, and the cost per hour has been increasing about $0.03 per hour each year. Overall cost per hour for the 45 months is $0.256 per hour. I have been paying $0.13 per KWH for electricity.  I have spent a total of $31.86 for electricity for runs over the 45 months.  Add in winter storage costs and the total cost of electricity is $37.03 This tells me that my batteries are aging slowly, but still have plenty of life left.

sailracerMember since May 2022

I put in the new MightyMax 75Ah battery to replace my original battery that I concluded was bad and it seems to be working perfectly.  So far I don’t see any evidence of a problem mixing Leoch and MightyMax.  The terminal positions are slightly different on the MightyMax but the battery jumpers still reach them easily, and it has a fabric lifting strap instead of plastic handles.  I mowed last night and finished with 35% battery remaining instead of either flashing 5% or blades shutting off before I was done, so it looks like it was another premature Leoch battery failure and replacing it resolved the problem.

 

Here’s a picture.  I discovered this morning I forgot to put the plastic battery covers back on.  Is it worth taking everything apart again to put them back on or should I just run without them until the next time I need to service a battery?

 Photo from the original forum

jamisMember since Apr 2010

The battery covers are for dust protection, so it’s your choice. If it were mine, I’d put them on. Glad to hear the new battery works. 

sailracerMember since May 2022

jamis wrote:

On 5/25/2022 at 10:15 PM, jamis said:

As to the CCA question, I can only say that Ryobi’s troubleshooting process is to run a load test on the batteries to see what the condition is. The $40 load tester my neighbor bought, and the commercial load tester the local battery shop used, both measured voltage drop under load vs time to determine the health of the batteries. I’m no expert, but if that’s what the manufacturer says is to be done, that’s what I’ll do. I also find it interesting that both Leoch and MM deep discharge style batteries don’t list the CCA of these batteries. I do know the Leoch batteries are used in wind farms, solar arrays, UPS installations, and mobility devices where CCAs are not important. 

I’ll add my conclusions after experimenting with my batteries and tester.  For a typical car battery for starting an engine, CCA is important.  The batteries are designed for supplying large amps over a short period of time.  They are also not meant to be deep discharged and need to be fully charged to operate effectively, so car starting batteries are tested at full charge.  Deep cycle batteries aren’t designed for outputting large amounts of current over a short time but instead are designed to output a working current for a long period of time and be able to sustain that current as the battery discharges.  Deep cycle batteries can still generate a large current in short time, but the amount of that current is dependent on the state of charge and may not be a good indicator of battery health, so any tester that only tests for a short period of time may not be able to detect a problem with a deep cycle battery, particularly if it is a problem that requires heat build up in a battery to show up.

 

The small, consumer load testers like the one I tried, are designed for measuring that peak current over a very short period of time and the tester determines health by comparing that current to the rated CCA of the battery.  The much bigger commercial load testers are likely using a test method with better heat dissipation so they can test for a longer period of time and can observe voltage drop over that time period.  They can safely apply a load for many seconds to see if the battery charge can hold up over that longer period of time.  That seems more likely to find a problem with a deep cycle battery, but still may not be sufficient.  If the load current is high, it isn’t testing the deep cycle battery the way it was intended to be used.  If the load current is lower, it may take a long time to determine its state of health.  Looking at the battery discharge graph I posted earlier, using highest current discharge they show (depletes the battery in 30 minutes, which extrapolating from tables in the datasheet suggests the current is around 85A) it takes 8 minutes of load at 85A for the voltage to drop from 11.9V to 11.6V.  To test that, the load tester would have to dissipate >1000W for 8 minutes.  That’s a big toaster worth of heat!

 

The measured CCA with my small meter showed approximately 40A of difference between the 4 batteries in my mower when fully charged.  The battery that ended up being bad was actually one of the ones with a high CCA measured by the charger.  With the blades running (drawing an approximately constant load I estimate to be around 30A) all of the batteries had a very similar measured voltage when all were fully charged.  Even the bad battery was able to output the required current without showing an abnormal voltage drop when fully charged.  Depending on how much current a battery load tester draws and for how long, it may not detect a problem with this battery when fully charged.  Once the deep cycle batteries had been discharged more, things started to change.  The consumer battery tester showed the CCA of all 4 batteries dropped.  The bad battery dropped more than the others, but was still putting out 360 CCA when mostly discharged.  The others were at 400 to 430.  That alone can’t diagnose the problem, but now the voltage on the bad battery was reading only ~10.5V while under load whereas the good batteries were still at 12.3V.  Another clue- the bad battery had a spot on the case that felt hot to the touch after discharging for an hour.  I don’t know that any load tester can run a battery long enough for it to heat up internally like that.  Maybe there is some clue in the voltage/current before the battery heats up or at much higher currents maybe it shows up quickly.   Maybe someday if I get around to it, I will take my bad battery to a shop for testing to see what they say.

 

In terms of power, the bad battery is putting out a little bit less than the good batteries.  Since they are wired in series, the current through them is the same, only the voltage differs, so the bad battery is putting out about 15% less power than the good ones based on the voltage difference.  The Ryobi battery management seems to key off voltage for battery state of charge, however, and thinks that this much drop in voltage means the pack as a whole is more discharged than it actually is.  The battery still seems to have the charge in it, but is not capable of outputting it at the current required which causes the voltage to drop.  If the bad battery sits and cools down, the voltage comes back in line with the other batteries and the Ryobi gauge goes from reading 5% up to 40% and is happy again and the mower can run for longer.   So, whatever is wrong with my battery internally, it seems marginal right now (but getting worse over time) and only shows itself when the battery has been running long enough to build up some heat internally.

 

For those trying to determine if it is time to replace all of your batteries and want to diagnose it yourself, I would say do an extended load test to determine if there is one battery in particular causing your pack voltage to drop as the batteries discharge or if all of your batteries are dropping the same and have worn out evenly.

 

 

glennfinMember since May 2022

That’s great news about the MAX battery!,,,, I will be changing all the batteries and there will be considerable savings if I go with the MM’s. Did you have any issues with charging? Also, did you pre -charge the MM before you installed it? I’m assuming you did..

 

sailracerMember since May 2022

glennfin wrote:

On 5/30/2022 at 10:27 AM, glennfin said:

That’s great news about the MAX battery!,,,, I will be changing all the batteries and there will be considerable savings if I go with the MM’s. Did you have any issues with charging? Also, did you pre -charge the MM before you installed it? I’m assuming you did..

 

So far I haven’t had any issue with charging.  The mixed pack charged back to 100% (52.9V) overnight.  I’ll check later this week to see if it has the self discharge problem where it drops a volt and reports 70% when on the charger for a week or more.

 

The MM battery ordered from Amazon came mostly charged I think.  It read 13V when it arrived.  I put it on a trickle charger for 24 hours before installing it in the mower with the other fully charged batteries.

jamisMember since Apr 2010

FWIW, as the batteries in my RM480e age from use & charging, I’m documenting an increase in the cost per hour of use at $0.01 per hour each year. In other words, it now costs $0.04 per hour more to run my mower than it did the first year. Since everyone uses their mower differently and each use can have different factors, this is the one measurement that I think reflects how to measure the battery aging process.  As of today, the cost per hour is at $0.258. By comparison, my neighbor’s Toro V-Twin rider uses a gallon of gas per hour and the current price of 87E10 is $4.799/gal.

sailracerMember since May 2022

sailracer wrote:

On 5/31/2022 at 8:07 PM, sailracer said:

So far I haven’t had any issue with charging.  The mixed pack charged back to 100% (52.9V) overnight.  I’ll check later this week to see if it has the self discharge problem where it drops a volt and reports 70% when on the charger for a week or more.

 

This week the mower was still at 100% after sitting for a week on the charger.  While I wouldn’t call this conclusive, it is a datapoint supporting the idea that the 70% reading problem could be related to a bad battery self-discharging faster than good batteries.  I’ll keep checking as the time between mowings increases later in the summer.

 

Update- one week later and the 70% problem returned.  I did notice that the finishing % when I was done with my lawn was the same as the week before when it started from 100%, so it seems like it must just be a voltage variance sensitivity reading when the batteries are fully charged and doesn’t really reflect 30% less energy in the batteries.

TotalRexMember since May 2022

HELP,

Anyone know who has a replacement battery for the RM480e in stock?  Home Depot’s site says they do, but I ordered one two weeks ago and they keep emailing me that shipping is delayed.  They do not have them in stock.

 

I just need one right now.  One of my batteries is dead according my tester while the are 3 are ‘OK’

jamisMember since Apr 2010

Apparently, the Mighty Max SLA/AGM batteries sold by HD work in these mowers.

 

My neighbor ordered one of the 100 ahr. Leoch batteries from HD three weeks ago and received it within days. It restored his mower’s performance to like new.

TotalRexMember since May 2022

I replaced a bad battery with a new one, but I am getting the same results.  The mower runs for few minutes then stops moving.  If I lift off the pedal it moves again for a few feet than stops.  Then the blades turn off.   I can then drive it back to the garage but only slowly.  If I push all the way down on the pedal it goes for a few feet then stops. 

 

WilI need to replace all the batteries?  Or should I try one more?

My tester says the other 3 batteries rate at ~380-400 CCA if that helps.  The new battery says ~500. 

TotalRexMember since May 2022

TotalRex wrote:

1 hour ago, TotalRex said:

I replaced a bad battery with a new one, but I am getting the same results.  The mower runs for few minutes then stops moving.  If I lift off the pedal it moves again for a few feet than stops.  Then the blades turn off.   I can then drive it back to the garage but only slowly.  If I push all the way down on the pedal it goes for a few feet then stops. 

 

WilI need to replace all the batteries?  Or should I try one more?

My tester says the other 3 batteries rate at ~380-400 CCA if that helps.  The new battery says ~500. 

 

An update.  I had a 2nd new battery and so I replaced a 2nd old one (long story HD sent me an order I cancelled).  I guess that raised the total power to be enough to run the mower.   I was able to mow the front lawn without it stopping this time.   I am going to fully charge it again and try my back yard which is a little over 1/3rd of an acre.

 

Question, I read to wait until batteries cool down before recharging.  Is that true?

CerberusMember since Jun 2022

So where can you get the batteries tested to see if they are failing? I tried my local Batteries Plus and they said they don’t test SLA batteries. Should I be looking at lawn/garden or automotive places?

jamisMember since Apr 2010

TotalRex: the charging system has a thermistor connected to the batteries to prevent overheating during the charging cycle. It’s that little black wire and white connector at the rear of the battery pack. It is wired into the safety and control logic circuits in the back of the charging receptical.  Testing a SLA/AGM deep discharge battery with a CCA tester is not the correct method. It won’t give you the correct results for this application. They need to be tested with a proper load tester for the deep discharge use. 

 

 Cereberus: My local battery shop (Battery Wholesale) had no issues testing my SLA/AGM batteries for free even. Some new cars have SLA starter batteries, so maybe the auto parts shops can test them. Have any Interstate Battery stores around?  How about trying a golf course cart shop to see if they can offer suggestions? Suggest Batteries Plus isn’t very PLUS. Is there no other battery shop in the area? My neighbor bought a 100 amp battery load tester from Amazon for less than $40 to test his.

jamisMember since Apr 2010

I discovered an interesting fact about the batteries in my RM480e. My mower is in its fifth mowing season and my recorded data shows that as the batteries age, the cost per hour of operation is increasing. The cost per hour has gone up 1.3 cents per hour per year.  So now the cost per hour to mow is at 25.8 cents per hour. I don’t see any run time reduction, just a bit more charging watts. To put that into perspective, my neighbor’s 42″ Toro Timecutter V-Twin burns a gallon of 87E10 per hour. When I bought my mower, gas was $2.50 a gallon, it’s now $5.10 a gallon. That makes my electric mower 19.76 times less expensive to use. I have spent a total of $32.78 for electricity to mow lawns for over 46 months. Including winter storage, the total electricity cost has been $37.94, or 82 cents per month of ownership.

JeremyAMember since Jul 2021

Jamis – what load tester did your neighbor buy?

jamisMember since Apr 2010

JeremyA wrote:

12 hours ago, JeremyA said:

Jamis – what load tester did your neighbor buy?

Not sure. It was less than $40 and he got it off of Amazon. I think it is this one, because it has the switch at the bottom for starting/stopping the test without messing with the leads.

 

https://www.amazon.com/OEMTOOLS-24338-100A-Battery-Tester/dp/B07FQ1G327/ref=sr_1_8?gclid=Cj0KCQjwhqaVBhCxARIsAHK1tiN3qLLzu-Q-aGD4vR5O16SRyYdCN6yc2GAORc2jd1v3WfKm92KFzGcaAlsCEALw_wcB&hvadid=580743546407&hvdev=c&hvlocphy=9015090&hvnetw=g&hvqmt=e&hvrand=14902647177619769028&hvtargid=kwd-398861394456&hydadcr=7501_13212144&keywords=battery+load+tester+100+amp&qid=1655341525&sr=8-8

CRPMember since Jun 2022

Breischaft wrote:

On 6/24/2021 at 9:22 AM, Breischaft said:

my lack of attention to detail:  only beeps when left lever pushed or pulled, leading to the main drive not the slave. 

 

Ok, so I am new to this… unpacked it and assembled it per instructions. The moment I went to drive it off the metal crate, this happened to me. Left lever makes it beep and there is no forward or backwards movement. Blades engage so it’s not the switch under the seat. Anyone have any ideas to what this might be? I mean, I know it’s frustrating as F%*k but that’s about all I can gather at this point!! Any help?

CerberusMember since Jun 2022

jamis wrote:

On 6/11/2022 at 7:01 PM, jamis said:

 Cereberus: My local battery shop (Battery Wholesale) had no issues testing my SLA/AGM batteries for free even. Some new cars have SLA starter batteries, so maybe the auto parts shops can test them. Have any Interstate Battery stores around?  How about trying a golf course cart shop to see if they can offer suggestions? Suggest Batteries Plus isn’t very PLUS. Is there no other battery shop in the area? My neighbor bought a 100 amp battery load tester from Amazon for less than $40 to test his.

Thanks for the tips! Interstate in the area tested them – only charged me $5 and probably only because I asked how much. All four batteries tested bad and Ryobi is sending me a completely new set. From what I saw, the mower was mfg in 2019 and I bought last year. I’m guessing the time in storage probably trashed the batteries. BTW – the only reason I got to this point was reading this thread. So much good info here. Most appreciated.

CRPMember since Jun 2022

CRP wrote:

16 minutes ago, CRP said:

Ok, so I am new to this… unpacked it and assembled it per instructions. The moment I went to drive it off the metal crate, this happened to me. Left lever makes it beep and there is no forward or backwards movement. Blades engage so it’s not the switch under the seat. Anyone have any ideas to what this might be? I mean, I know it’s frustrating as F%*k but that’s about all I can gather at this point!! Any help?

 

CRP wrote:

17 minutes ago, CRP said:

Ok, so I am new to this… unpacked it and assembled it per instructions. The moment I went to drive it off the metal crate, this happened to me. Left lever makes it beep and there is no forward or backwards movement. Blades engage so it’s not the switch under the seat. Anyone have any ideas to what this might be? I mean, I know it’s frustrating as F%*k but that’s about all I can gather at this point!! Any help?

Btw, after reading the thread I went out and counted, I have 11 beeps, not 12.

 

This is infuriating!

jamisMember since Apr 2010

CRP: Since your mower is brand new, you really need to contact Ryobi for assistance. Use all of the information from the label under the seat when you call them. I’m not that familiar with the ZT4480s so contacting Ryobi is the best I can offer at this point.

 

Since none of the supplied manuals discuss the number of beeps, Ryobi definitely needs to be contacted.

 

Just remembered I have the troubleshooting guide for the ZT480 mowers and upon checking, there is no stated beep count for any issues.  Still the best thing to do is to contact Ryobi with a warranty issue.  Also find out where the nearest Ryobi Authorized Outdoor Service Center is.  Be aware that the one nearest me (1.5 mi.) is horribly backlogged with repairs as they also do John Deere, Honda, Stihl, and Toro stuff.  HD has a 90 day return policy also.  Here’s what the troubelshooting manual states for the mower not moving:

 

If the mower will not drive
a. Make sure the seat switch is functional and activated.
b. Test the angular transducers. Replace if necessary.
c. Test the neutral switches. Replace if necessary.
d. Test the brake switch. Replace if necessary.
e. If the mower still will not drive, test the Drive Motor controllers. Replace if necessary.
f. Test the drive motors and Hall sensors, replace as necessary

jamisMember since Apr 2010

Cerberus: Leoch states the LPC12 batteries can sit for up to six months without a maintenance charge if stored in the proper conditions.  And they and Ryobi stated they should be maintained at least every month once used in the mower. Probably why Ryobi is replacing them all.  When they replaced my one failed battery under warranty, It was overnighted via UPS.  

CerberusMember since Jun 2022

jamis wrote:

On 6/20/2022 at 11:30 AM, jamis said:

Cerberus: Leoch states the LPC12 batteries can sit for up to six months without a maintenance charge if stored in the proper conditions.  And they and Ryobi stated they should be maintained at least every month once used in the mower. Probably why Ryobi is replacing them all.  When they replaced my one failed battery under warranty, It was overnighted via UPS.  

Yeah, with the weight of all four it’s coming common carrier. Good news is I’m getting good at taking the batteries in and out so it won’t take me long to swap them 😉

 

BTW – I think there was mention of a service manual for the RY48ZTR75 at one point. Is that available anywhere? My searches have come up dry…  

You are the influencer. Post it to 4.4 million followers.

Hit record. We’ll handle the rest.

Upload your review