SharkBite Copper Press Fittings: No More Sweating Pipes

We may earn a commission from links on this page. Affiliate disclosure

Copper press tee held in a hand, and copper press fittings installed on copper water lines in a basement

Disclosure: SharkBite sponsors the Tools In Action channel. Our opinions are our own.

Quick quiz: who makes this copper press fitting? If you said SharkBite, you’re right. Most people think SharkBite only makes push-to-connect fittings. They actually make real copper press fittings, too. In this short, we use them on a copper install and show why pressing is so satisfying.

What It Is

SharkBite’s Copper Press line is made up of press fittings for joining copper tube with a press tool instead of a torch. On sharkbite.com, SharkBite describes its Small Diameter Copper Press fittings as:

  • A flame-free copper pipe connection.
  • Made from C12200 copper.
  • Fitted with a pre-installed EPDM seal.
  • Compatible with ASTM B88 Types K, L and M copper pipe.
  • Able to be installed on wet or dry lines.

The line includes couplings, 45° and 90° elbows, street elbows, reducing elbows, caps, reducers and more, in small and large diameters. Check SharkBite’s site for the exact fittings and sizes you need for your job.

What the Video Shows

The process works like any other copper press fitting:

  1. Put the fitting on the pipe.
  2. Make your lines so you know the fitting is fully seated.
  3. Put the press tool jaws on the fitting.
  4. Pull the trigger and let the tool complete the press.

There’s just something satisfying about that sound.

Quick tip from the video: Sometimes the tool’s jaws feel stuck on the fitting after a press. If that happens, rotate the tool a little bit, and it’ll break free.

We do one more just because, and then we show the finished work. It’s a finished run of SharkBite fittings that we installed for Eric. The ASMR clip we posted a couple of weeks later shows more SharkBite copper press fittings being pressed on copper.

To finish, we joke about the fitting selection: tees, right angles, all of it. SharkBite is a full-service plumbing supplier. If it has to do with pipe, they probably make a connection for it.

Takeaways From the Video

What we liked:

  • No torch. SharkBite calls these flame-free, which matters around finished walls, wood framing and anything else that can burn.
  • It’s fast. Mark, place the tool, press, and move on. No flux, no solder and no waiting for a joint to cool.
  • It’s consistent. The tool does the work the same way every time.
  • Wet or dry lines. SharkBite says these can go on either one, which helps a lot on a repair where you can’t get a line completely dry.

Things to keep in mind:

  • You need a press tool. Copper press fittings require a compatible press tool and jaws, which are a real investment. Check SharkBite’s tool compatibility for the fittings you’re buying.
  • Prep still matters. SharkBite’s instructions are to cut the tube to length, deburr and clean the surface, and measure and mark the insertion depth before pressing.
  • Use the tip. If the tool sticks, rotate it a little. Don’t yank it.

Press vs. Solder vs. Push-to-Connect

If you already own a press tool, copper press fittings are hard to beat for speed and consistency on copper. If you don’t, sweating joints is still the low-cost option, but it takes skill, flux, solder and a flame. Push-to-connect is the no-tool option for repairs and transitions. SharkBite makes fittings for all three styles of work, and that’s the point of this video.

Who It’s For

SharkBite copper press fittings are for plumbers and serious DIYers who work on copper and own, or plan to buy, a press tool. They’re a great fit for water treatment installs like the water softener in this video, mechanical rooms, and repairs where you don’t want an open flame.

Watch the short above, and let us know in the comments: do you press, sweat or push?

Where to buy: SharkBite Copper Press fittings

Leave a Reply

Your email address will not be published. Required fields are marked * First-time comments are reviewed before they appear.

Comment on FacebookJoin the conversation on our Facebook page.

You are the influencer. Post it to 4.4 million followers.

Hit record. We’ll handle the rest.

Upload your review