My main bathroom remodel

KnarlyCarlMember since Jan 2016

I love it, that’s so awesome you’re building your vanity. I built all my kitchen cabinets, I’m realizing now I didn’t take enough pictures, because I can’t remember how I put together half of them ha

 

Love the centipede!!

 

rrich1Member since Jun 2015

phffter wrote:

my sons are 27 and 24. yours are still young. mine should know better.

lines……………. depends. i spent alot of time on both baths with the soffits, so i would have an unbroken line and uncut tiles, from floor to ceiling, along the outside edge of the tub, front and back. upstairs i was dead nutz on. this one, im a little out in the back. dont know how, everything is square. i dont think it will that that noticeable.

I mathed out where the lines should be for the grout and cut out and installed the horizontal pieces in the wall for the niche. My luck I will be ever so slightly off. I think I am going to cut out where I made the niche and get the cement board in. Then I can waterproof that area. I think it will come out just fine.

Sent from my XT1254 using Tapatalk

rrich1Member since Jun 2015

KnarlyCarl wrote:

I love it, that’s so awesome you’re building your vanity. I built all my kitchen cabinets, I’m realizing now I didn’t take enough pictures, because I can’t remember how I put together half of them ha

 

Love the centipede!!

 


Thanks. We need a kitchen remodel and I would love to build the kitchen cabinets as well. I think I could justify a track saw purchase then! Lol.

I purchased the centipede just for this job. Been very pleased with it so far.

I used to take a lot of pics it have been slacking on that lately. I will get some more.

Depending on how getting the lighting placing figured out I will try and get a coat of primer on the ceiling tomorrow.

Sent from my XT1254 using Tapatalk

rrich1Member since Jun 2015

Between yesterday and today. I got the ceiling lights measured out and cut. I put a coat of primer on the ceiling. I measured and cut the ditra for the floor but am 2 feet short! Crap! I texted a friend who does tile work and he didn’t have any extra so that means I get to spend $80 on another roll. The only good thing about it is that whenever we redo our master bath the rest of that roll will cover it or when I redo the kitchen I can use it in there. Still irritating.

I was also able to get some major work done on the vanity. I think I am going to start a separate build thread in the woodworking forum. I got the lower shelf measured and cut out. I attached the sides and went ahead and stained the plywood shelf.

[External image (uploads.tapatalk-cdn.com), not copied][External image (uploads.tapatalk-cdn.com), not copied]

Sent from my XT1254 using Tapatalk

rrich1Member since Jun 2015

Today I after the kids went with the sister in law I was able to cut the niche out and the back piece cut before I had to go to work. After work I was able to get the vanity prepped (pre stain) and then stained. I guess I’m at the point of no return huh? I definitely want to make some stuff out of cherry in the future with no stain. I like the ebony a lot though. You can see the grain throughout and it looks really nice. I believe it will darken as time goes on and that is fine.

[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]

Sent from my XT1254 using Tapatalk

KnarlyCarlMember since Jan 2016

Just seeing the transformation of that color on the vanity is awesome, I can already picture it in a bathroom and it’s looks incredible in my head lol, hope it turns out like you want.

 

I made a piece in my teens and experimented with vinegar and steel wool, THAT was some dark stain, it was so much fun watching the transformation take place

rrich1Member since Jun 2015

KnarlyCarl wrote:

10 hours ago, KnarlyCarl said:

Just seeing the transformation of that color on the vanity is awesome, I can already picture it in a bathroom and it’s looks incredible in my head lol, hope it turns out like you want.

 

I made a piece in my teens and experimented with vinegar and steel wool, THAT was some dark stain, it was so much fun watching the transformation take place

I really like the vanity so far. im surprising myself on how well it is turning out so far. lol.

rrich1Member since Jun 2015

last night after work I started to waterproof the tub area. While starting to waterproof the niche, I may have made a mistake with it. I tried to make it a large size and I may have made it too close to the edge of the tub. ill post some pics and tell me what you think. also with it so close I might change up the design of the bullnose a little bit. the original plan was to stop the bullnose at the edge of the tub to keep one straight line up. now I am thinking I should put one whole bullnose tile in front of the tub and run that straight up to the celing. what do you guys think?

 

 

DaveJr.Member since Nov 2015

Looks great! We’re in the process of planning out our own bathroom remodel. Hoping to start after the holidays.

rrich1Member since Jun 2015

[External image (uploads.tapatalk-cdn.com), not copied]

Sent from my XT1254 using Tapatalk

rrich1Member since Jun 2015

Talked with a friend who tiles for a living. He didn’t seem to think it was an issue. I got the niche coated I put a second coat on the rest last night after I worked on my router table.

Still on schedule to start tiling tomorrow eek! [emoji33]

Sent from my XT1254 using Tapatalk

rrich1Member since Jun 2015

[External image (uploads.tapatalk-cdn.com), not copied]

Well that is frustrating!

Sent from my XT1254 using Tapatalk

KnarlyCarlMember since Jan 2016

Gotta get a full new roll huh?

So you think just the bullnose pieces straight up from the edge of the tub will slip by the niche pretty nice? It’s probably going to look great either way but if you take it another row past the tub edge, take it all the way down to the floor probably

rrich1Member since Jun 2015

KnarlyCarl wrote:

Gotta get a full new roll huh?

So you think just the bullnose pieces straight up from the edge of the tub will slip by the niche pretty nice? It’s probably going to look great either way but if you take it another row past the tub edge, take it all the way down to the floor probably


Yup. Got a whole new roll for that. Luckily my brother in law is redoing a room and will start with my roll and pay me for it.

The bull nose would be cut thin if it went straight up from the tub end at the much area. The new plan is to go all the way to the edge of that wall and match it on the other side.

Tiling progress so far. Will finish it up tomorrow. I have a few low spots [emoji35]
[External image (uploads.tapatalk-cdn.com), not copied]

Sent from my XT1254 using Tapatalk

KnarlyCarlMember since Jan 2016

Yeah with that lighting, it really shows the shadows where the low pieces are

rrich1Member since Jun 2015

KnarlyCarl wrote:

Yeah with that lighting, it really shows the shadows where the low pieces are


The few front pieces aren’t in in that pic. Also some of those dark spots actually aren’t low/high. Not as many as it makes it out to be.

I got the tiling finished before work today. I also got the drawers cut out and pieces cut for my router fence as well. Going to make it pretty basic right now and modify it later to make it more modular.

Sent from my XT1254 using Tapatalk

rrich1Member since Jun 2015

this past weekend my neighbor came by and rewired the electrical for me. I wanted to have the ceiling painted before the lights went in but that was a no go. I had put painters tape on the ceiling after I primed it so I wouldn’t get any of the redguard on the ceiling when I waterproofed the tub area. well that ripped the top layer of the drywall off. so I had to mud that. I got it primed last night and will paint it with ceiling paint tonight.

 

the floor tile is all laid down but I am going to tear a piece up. it is low and right in the center. I have another low spot but that is under the vanity so I don’t care about that one.

 

plan/goal is to tile the tub area wed/thurs this week. if I get that done it is all home stretch from there. I made a fence for the router table so I can get the drawers cut when I dial the bit in.

rrich1Member since Jun 2015

Didn’t get nearly as much done as I wanted to this week. I had to take the wife to the hospital for a scheduled procedure so that took up some time. Getting the tub tile laid out was irritating for some reason and tool longer as well. Tomorrow before work I hope to have one more row of tile up plus the glass tile accent line up as well. I don’t want to start that if I can’t finish in time for work. If not I will finish up the drawers for the vanity. The drawer lock bit I can’t seem to dial in right now so i am using pocket holes for the drawers. They will be hidden in the front and back so you want see them.

[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]

Sent from my XT1254 using Tapatalk

rrich1Member since Jun 2015

3rd row is up and lined up how I wanted it to with the shower niche for a nice grout line. I also got one of the tiles on each side put up in front of the tub and cut the drawer bottoms for the vanity. Tonight after work I am debating doing the glass tile so that can cure and harden so I can put up the rest of the shower tile. I added some mortar to the back to help bring it up for the glass tile. Really wish I had made the boards more level so I wouldn’t be wasting so much mortar. Oh well. First timer here. I am also really bad about cleaning the tile as I go. Lol.
[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]

Sent from my XT1254 using Tapatalk

DaveJr.Member since Nov 2015

Looking pretty good!

rrich1Member since Jun 2015

Thanks. Getting everything as level and plum is so tedious. These bigger tiles slope some at the edges so everything isn’t exactly flat but as good as it can be. I am really excited to get it finished this week (tile work anyways).

Sent from my XT1254 using Tapatalk

rrich1Member since Jun 2015

Last night after work I got the drawers done. Still need to get the fronts completed though.

Sent from my XT1254 using Tapatalk


[External image (uploads.tapatalk-cdn.com), not copied]
rrich1Member since Jun 2015

glass tile is going to be the death of me…that is all.

JimboS1iceMember since Sep 2015

rrich1 wrote:

15 minutes ago, rrich1 said:

glass tile is going to be the death of me…that is all.

 

oh ya that can be fun

rrich1Member since Jun 2015

JimboS1ice wrote:

1 minute ago, JimboS1ice said:

 

oh ya that can be fun

at work right now. I tried to get the back wall done but that just wasnt happening. I built up the wall some more with mortar and letting that dry. Hopefully it will allow the tiles to stick with less mortar to make it slide down. I did get the glass tile on for the back of the niche. 

 

I am in a design question with it right now though. My glass tile is in one big stripe that goes through the niche. I plan to do the top and bottom with the wall tile. But am wondering if I should do the sides in the wall tile as well or with the glass tile. Ill get a pic when I go on lunch to clarify this. 

KnarlyCarlMember since Jan 2016

rrich1 wrote:

4 hours ago, rrich1 said:

at work right now. I tried to get the back wall done but that just wasnt happening. I built up the wall some more with mortar and letting that dry. Hopefully it will allow the tiles to stick with less mortar to make it slide down. I did get the glass tile on for the back of the niche. 

 

I am in a design question with it right now though. My glass tile is in one big stripe that goes through the niche. I plan to do the top and bottom with the wall tile. But am wondering if I should do the sides in the wall tile as well or with the glass tile. Ill get a pic when I go on lunch to clarify this. 

I get it. I think if it looks right, do it all with the glass tile. I’ve seen it with the wall tiles in the niche at some jobs, and seen glass tile in the niche at others. In my opinion, I thought the glass tile looked cool, but as you may know, i’m completely unbiased and indifferent to tile LOL

rrich1Member since Jun 2015

KnarlyCarl wrote:

I get it. I think if it looks right, do it all with the glass tile. I’ve seen it with the wall tiles in the niche at some jobs, and seen glass tile in the niche at others. In my opinion, I thought the glass tile looked cool, but as you may know, i’m completely unbiased and indifferent to tile LOL


Pic of the niche. Looks brownish but it isn’t. Decided to have the niche be seamless from left to right with the glass tile on both sides of the niche. The top and bottom will be the bullnose tile.
[External image (uploads.tapatalk-cdn.com), not copied]

Sent from my XT1254 using Tapatalk

rrich1Member since Jun 2015

Tonight after work I was able to out the first coat of clear on the body of the vanity. Still don’t have the drawer fronts done yet :(. I also just to finished priming the walls. Going to be a very busy week and trying not to waste any time.

Sent from my XT1254 using Tapatalk

DaveJr.Member since Nov 2015

Looks great Rich!

rrich1Member since Jun 2015

It’s driving me insane with how slow this tile work is going for me. The glass tile is done though…finally. I’m not the happiest with it but it will work. Each ro moves independently of each other and there are waves in it. Can’t really tell though.

[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]

Sent from my XT1254 using Tapatalk

phffterMember since Mar 2016

looking good.

i used 1/16 spacers on the glass tile.

if you havent done it yet, it’s going to be a bear to get the mortar out of the grout lines once it’s set.

im picking the stuff out now.

BigmikezMember since Jun 2013

rrich1 wrote:

2 hours ago, rrich1 said:

It’s driving me insane with how slow this tile work is going for me. The glass tile is done though…finally. I’m not the happiest with it but it will work. Each ro moves independently of each other and there are waves in it. Can’t really tell though.

[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]

Sent from my XT1254 using Tapatalk
 

Looking good ??

rrich1Member since Jun 2015

phffter wrote:

looking good.

i used 1/16 spacers on the glass tile.

if you havent done it yet, it’s going to be a bear to get the mortar out of the grout lines once it’s set.

im picking the stuff out now.


Did some yesterday and tried to do some along the way.

Sent from my XT1254 using Tapatalk

rrich1Member since Jun 2015

Getting closer. [External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]

Sent from my XT1254 using Tapatalk

rrich1Member since Jun 2015

Need some opinions on the floor transition. We are thinking of running the dark tile and bull nose all the way to the floor and then butting the base board to it. Or would it be better to run the base board all the way to the tub and then stopping the tile at the top of the base board?

Sent from my XT1254 using Tapatalk

DaveJr.Member since Nov 2015

rrich1 wrote:

5 hours ago, rrich1 said:

Need some opinions on the floor transition. We are thinking of running the dark tile and bull nose all the way to the floor and then butting the base board to it. Or would it be better to run the base board all the way to the tub and then stopping the tile at the top of the base board?

Sent from my XT1254 using Tapatalk
 

I think that would be more of an opinion. Try it both ways with some scrap and see which way you prefer.

phffterMember since Mar 2016

rrich1 wrote:

19 hours ago, rrich1 said:

Need some opinions on the floor transition. We are thinking of running the dark tile and bull nose all the way to the floor and then butting the base board to it. Or would it be better to run the base board all the way to the tub and then stopping the tile at the top of the base board?

Sent from my XT1254 using Tapatalk
 

what kind of baseboard? wood? different tile for trim?

thickness differences?

rrich1Member since Jun 2015

Ahhhhhhhhhhh. I was so close to finishing before work today. I slipped and fell last night when I parked. Nailed my back and slammed my neck on my trucks nerf bar. Got going late and wasn’t going as fast. Wearing g a duty belt isnt helping anything today. Also I had planned to just be able to cut the top row setting the saw up once…Whelp that didn’t happen. Of course I had to angle the tops to get a consistent enough line. Also some how I had miss measured at least one piece and had to recut it. Taking even more time. Anywho. Here is how it looks right now. I went all the way to the floor with the tile. I think it looks good.
[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]

Sent from my XT1254 using Tapatalk

phffterMember since Mar 2016

looking good

rrich1Member since Jun 2015

thanks guys.

 

last night after work I put a 1st coat of paint on one wall to see how it would look with the tile. wife decide to stick with a medium gray instead of dark for the wall tile. I pulled up another floor tile today and got it cleaned out. hoping tonight to finish up all of the tile work. clean up the tile as best I can and then hopefully grout sometime tomorrow.

rrich1Member since Jun 2015

I feel like I actually made some progress in the past 24 hrs. Last night after work I got the rest of the wall and floor tiles in. Today I got the first coat of paint on (minus near the tiles), got most of the shower cleaned for grout (niche area still needs done and will be the worst spot). And just before work tonight I got grout onto the floor.
[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]

Sent from my XT1254 using Tapatalk

JMGMember since Dec 2015

Always amazing what a bit of color can do for a room.

rrich1Member since Jun 2015

JMG wrote:

Always amazing what a bit of color can do for a room.


Agreed. Wasn’t able to get the second coat on today.

Sent from my XT1254 using Tapatalk

rrich1Member since Jun 2015

Well I didn’t make my deadline. We had family over today and wanted it done before then. I wasn’t able to work on it much yesterday due to the wife’s family Christmas. Here is how it stands right now. The toilet and faucet are hooked up. Tub still needs to be put together and the drawer fronts need to be put on.

[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]

Sent from my XT1254 using Tapatalk

JMGMember since Dec 2015

Thar be light at the end of that tunnel… Looking sharp.

CATERPILLARMember since Jan 2016

rrich1 wrote:

33 minutes ago, rrich1 said:

Well I didn’t make my deadline. We had family over today and wanted it done before then. I wasn’t able to work on it much yesterday due to the wife’s family Christmas. Here is how it stands right now. The toilet and faucet are hooked up. Tub still needs to be put together.

[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]
[External image (uploads.tapatalk-cdn.com), not copied]

Sent from my XT1254 using Tapatalk
 

Looking hella nice man that is so cool the soap indent  and the color of the tile 🙂 keep up the good work 

rrich1Member since Jun 2015

Forgot I also have the mirror I need to put back up as well. I really want to make a frame for it before hand but we shall see.

Sent from my XT1254 using Tapatalk

KnarlyCarlMember since Jan 2016

Ooh ouch I cringed when I read about your slip!! Take it easy 

That looks so cool, I can see there are so many ways to put tile and make it look good depending on what it looks like as you go along….

rrich1Member since Jun 2015

KnarlyCarl wrote:

Ooh ouch I cringed when I read about your slip!! Take it easy 

That looks so cool, I can see there are so many ways to put tile and make it look good depending on what it looks like as you go along….


Thanks. Luckily I haven’t had any headaches or neck issues. My lower back is still swollen and I have a good bruise. A trooper I am friends with slipped the other day working and broke a few bones! He is out for at least 6mo! Yikes!

Sent from my XT1254 using Tapatalk

JimboS1iceMember since Sep 2015

Wow looks good rich


Sent from my iPad using Tapatalk

You are the influencer. Post it to 4.4 million followers.

Hit record. We’ll handle the rest.

Upload your review